Dr Fixit 112 Pidifin 2K Acrylic Cementitious Waterproof Coating 3 kg

Product Description

Dr. Fixit Pidifin 2K is a acrylic cementitious, polymer modified elastomeric, waterproofing & protective coating composed of best quality Portland cement, properly selected & graded aggregates, additives & acrylic emulsion polymer as a binder. It is applied to waterproof and protect concrete and masonry substrates.

Areas of Application: 

Dr. Fixit Pidifin 2K must be applied to new or old concrete substrates that are structurally sound.

• Excellent as a waterproof coating for bathrooms, kitchen sinks, balconies, etc.
• Ideal as a coating for waterproofing of chhajjas, canopies, etc.
• As waterproof coating on internal sides of domestic water tanks.
• Good for waterproofing of sloped roofs.
• As a waterproof coating for terraces of areas up to 100-150m2

Features & Benefits:

• Elastomeric – elastomeric flexible coating that accommodate cracks up to 2 mm with an elasticity of 40-50%
• Low water permeability – excellent resistance to ingress of water
• Adhesion – excellent adhesion to concrete and masonry surfaces
• Eco-friendly – Non-toxic with low VOC content
• CFTRI certified – as a “potable water safe” coating for waterproofing for water tanks 

Method of Application

1. SURFACE PREPARATION

• The surface of application must be thoroughly prepared by mechanical means, to remove all loose particles, laitance, etc.
• Oil and grease, if any, must be de-greased with suitable solvents. It then must be washed off with jet of water and brought to touch dry state. Any surface undulations, cracks and crevices must be duly filled or repaired with cement sand mortar mixed with latex polymers such as Dr. Fixit Pidicrete URP.

2. MIXING

• Shake the liquid component well to a homogenous milky colour.
• Use heavy duty slow speed mechanical mixer fitted with a suitable paddle for mixing the two components of the material.
• In a mixing vessel, slowly add the powder component in to the liquid under continuous stirring. Continue to stir thoroughly to achieve a lump free homogenous slurry.

3. APPLICATION

• It is important that any pipe inserts or sanitary fittings should have been fitted grouted with suitable products from the Dr. Fixit range well before taking up the application.
• Grout pipe inserts using Dr Fixit Bathseal Tape and Dr Fixit Bathseal Grout.
• It is mandatory that all works of plumbing and sanitation must be complete before taking up application of Dr. Fixit Pidifin 2K.
• The surface of application must be pre-wetted thoroughly with water & brought to a touch dry state. Take up the first coat application with a stiff nylon brush. Work well into the substrate, to ensure that all small undulations are completely filled with the coating.
• 6 to 8 hrs after completion of first coat, take up second coat application in a direction perpendicular to the first.
• Complete the application and leave to air cure for 2 days. A moist hessian cloth can be kept over the coated surface to protect it from the effect of direct sunlight, in case of bathrooms and internal areas. Leave the coating without water curing for 2 days at least.
• In new bathrooms, typically, Dr. Fixit Pidifin 2K must be applied all over the sunken slab portion and upwards over the masonry walls up to a height of 6-7 feet, i.e. Over the splash zone of shower, etc. to ensure complete waterproofing.
• For vertical walls in bathroom ensure internal plaster level is sound and leveled mixed with Dr. Fixit Pidiproof LW+, Apply 2 coats of Dr. Fixit Pidifin 2K on all over or shower area, sprinkle the coarse, quartz sand while the second coat is still wet. This will provide key for subsequent tile adhesive materials.

4. GENERAL WATERPROOFING AND WATERPROOFING OF WATER TANKS

• General waterproofing is applied in areas exposed to foot traffic, it must be protected with a screed overlaid, during the application itself.
• When the coating for internal walls of water tanks, after second coat sprinkle coarse sand on wet coating to facilitate plastering.
• If the membrane is applied in areas exposed to foot traffic, it must be protected with a screed overlaid, during the application itself.

Technical Specification

• Mix Component - Mix Ratio 1 : 2 (A : B)
• Polymer Content - > 18 %
• Water Absorption - < 6%
• Proprietary Polymer - High quality modified acrylic polymer
• Set-to-touch time: ASTM D 1640: 45 min
• Tensile Strength - as cast: ASTM D 412: 2.5 N/mm2
• Elongation at Break - as cast: ASTM D 412: 60 %
• Adhesion to Substrate: ASTM D 4541: 0.80 N/mm2
• Adhesion to Concrete at 7 day: ASTM D 4541: 1.75 N/mm2
• Immersion in water Adhesion to Concrete at 7 day: ASTM D 4541: 1.00 N/mm2
• Crack Bridging: ASTM C 836:1 mm
• 12 month storage in sealed container and room temperature

Buy Dr Fixit 112 Pidifin 2K Acrylic Cementitious Waterproof Coating 3 kg online in India at wholesale rates. If you have been looking for Dr Fixit 112 Pidifin 2K Acrylic Cementitious Waterproof Coating 3 kg dealers, your search ends here as you can get the best Dr Fixit 112 Pidifin 2K Acrylic Cementitious Waterproof Coating 3 kg distributors in top cities such as Delhi NCR, Mumbai, Chennai, Bengaluru, Kolkata, Chennai, Pune, Jaipur, Hyderabad and Ahmedabad. You can purchase Dr Fixit 112 Pidifin 2K Acrylic Cementitious Waterproof Coating 3 kg of the finest quality and rest assured to get the best in terms of both durability and performance. If you are bothered about the Dr Fixit 112 Pidifin 2K Acrylic Cementitious Waterproof Coating 3 kg prices, you can be totally sure to get the best rates as Industrybuying brings you genuine Dr Fixit 112 Pidifin 2K Acrylic Cementitious Waterproof Coating 3 kg rates and quality assured products only from the best of brands with exclusive brand discounts you won’t find anywhere else. Procure Dr Fixit 112 Pidifin 2K Acrylic Cementitious Waterproof Coating 3 kg today and avail the best offers on your purchase.