• Home /
• All Brands /
• MTM /
• Tooling and Cutting /
• Tool Holders /
• ER Collet Chucks

Have a question? Call us now at +91 9650660070

MTM ER Collet Chucks

Showing 36 out of 36 products

Sort by

Recommended New Price : Low to High Price : High to Low

Ships within 5 days

MTM ER Collet Chuck Adaptor SLA18 Type 15000 RPM (GLP: 63 - 160 mm)

By MTM

₹3,185 - ₹8,141

You save ₹1,382!

28.08% OFF

The MTM ER Collet Chuck Adaptor SLA18 Type 15000 RPM (GLP: 63 - 160 mm) is a tooling accessory for machining setups that require an adaptor with the specified SLA18 configuration. Its type designation helps differentiate it from other adaptor options during product selection, tooling management, and equipment preparation. The listed rotational speed of 15000 RPM and GLP range of 63 - 160 mm serve as key reference specifications when assessing whether this model matches the requirements of the intended machine and application. Before selecting the adaptor, check its mounting dimensions and connection interface against the relevant machine and collet chuck specifications. Confirm the meaning and measurement points of the stated GLP range through the manufacturer's technical documentation to ensure the dimensions are interpreted correctly. The operating speed of the complete tooling assembly must remain within the limits of every connected component. Secure installation and routine inspection are also important for identifying wear, damage, or fitting issues before operation. The MTM ER Collet Chuck Adaptor SLA18 Type 15000 RPM (GLP: 63 - 160 mm) can be considered for a suitable machining arrangement after its dimensions, interface, and operating requirements have been verified.

Type of Product : ER Collet Chuck Adaptor

ER Type : SLA18

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (7)

Ships within 5 days

MTM ER Collet Chuck Adaptor SLA16 Type 15000 RPM (GLP: 63 - 200 mm)

By MTM

₹2,595 - ₹9,675

You save ₹1,408!

25.42% OFF

The MTM ER Collet Chuck Adaptor SLA16 Type 15000 RPM (GLP: 63 - 200 mm) is intended for consideration in machining setups that call for an adaptor identified by the SLA16 type designation. This configuration can be distinguished from other variants when reviewing tooling inventories, comparing product specifications, or preparing a machine for a particular operation. The stated rotational speed of 15000 RPM and GLP range of 63 - 200 mm are useful selection parameters for assessing whether the product's listed details correspond to the planned tooling arrangement. To determine suitability, compare the adaptor's connection dimensions and mounting requirements with the machine interface and the associated collet chuck assembly. The manufacturer's specifications should be used to confirm all relevant measurements and operating restrictions before installation. The speed rating of the complete assembled tooling system must also be considered, since connected components may have different limits. Correct fitting, secure retention, and routine condition checks are important parts of responsible tooling maintenance. Examine the adaptor for wear, damage, or looseness before use, and do not operate equipment when the fit or condition is uncertain. The MTM ER Collet Chuck Adaptor SLA16 Type 15000 RPM (GLP: 63 - 200 mm) provides a defined set of identification details to support informed selection for compatible machining applications.

Type of Product : ER Collet Chuck Adaptor

ER Type : SLA16

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (10)

Ships within 5 days

MTM ER Collet Chuck Adaptor SLA14 Type 15000 RPM (GLP: 55 - 160 mm)

By MTM

₹3,185 - ₹8,023

You save ₹1,695!

25.49% OFF

MTM ER Collet Chuck Adaptor SLA14 Type 15000 RPM (GLP: 55 - 160 mm) offers a specific adaptor configuration for consideration during tool setup and equipment selection. The SLA14 designation distinguishes this version from other options in the MTM ER collet chuck adaptor range. Its listed operating speed of 15000 RPM and GLP dimensions of 55 - 160 mm provide key product details that can be checked against the requirements of the intended machine and application. When choosing an adaptor, review the mounting arrangement, required dimensions, and connection specifications before placing it into service. Compatibility should be confirmed using the machine manufacturer's documentation and the specifications for the associated collet chuck and tooling. Operating conditions must remain within the limits of the complete assembly, including the spindle and every connected component. Ensure that the adaptor is installed securely and inspect it periodically for visible damage, wear, or signs of an unsuitable fit. The MTM ER Collet Chuck Adaptor SLA14 Type 15000 RPM (GLP: 55 - 160 mm) is best selected after confirming that its designated type, dimensional range, and stated speed align with the planned machining setup.

Type of Product : ER Collet Chuck Adaptor

ER Type : SLA14

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (7)

Ships within 5 days

MTM ER Collet Chuck Adaptor SLA12 Type 15000 RPM (GLP: 60 - 160 mm)

By MTM

₹2,949 - ₹7,669

You save ₹1,695!

25.49% OFF

The MTM ER Collet Chuck Adaptor SLA12 Type 15000 RPM (GLP: 60 - 160 mm) is a machining tool accessory designed for applications that require a collet chuck adaptor with the specified SLA12 configuration. Its type designation helps users distinguish this option when organizing tooling components and selecting equipment for a particular machining setup. The stated maximum rotational speed of 15000 RPM and GLP range of 60 - 160 mm provide important reference details for checking suitability against the intended machine and tooling arrangement. Before installation, verify the adaptor's mounting interface, dimensional requirements, and connection details against the machine specifications and relevant manufacturer documentation. The selected collet chuck arrangement should be appropriate for the workpiece, cutting tool, and planned machining operation. Confirm that the complete spindle and tool assembly is rated for the intended operating speed rather than relying on the adaptor's stated RPM alone. Proper installation and regular inspection can help identify wear, damage, or looseness before use. The MTM ER Collet Chuck Adaptor SLA12 Type 15000 RPM (GLP: 60 - 160 mm) can be evaluated as part of a compatible tooling setup where its listed configuration and dimensions meet the application requirements.

Type of Product : ER Collet Chuck Adaptor

ER Type : SLA12

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (7)

Ships within 5 days

MTM ER Collet Chuck Adaptor SLA10 Type 15000 RPM (GLP: 50 - 160 mm)

By MTM

₹2,949 - ₹7,669

You save ₹1,695!

25.49% OFF

The MTM ER Collet Chuck Adaptor SLA10 Type 15000 RPM (GLP: 50 - 160 mm) is a tooling component designed for compatible machining arrangements requiring an SLA10-type adaptor connection. Its type designation helps users distinguish this model from other variants and supports accurate identification during tooling selection. With a listed rotational speed of 15000 RPM and a GLP range of 50–160 mm, the adaptor provides useful reference specifications for evaluating its dimensional suitability and compatibility with the intended machine and collet chuck arrangement. Before purchase, verify that the SLA10 interface matches the required machine connection and tooling configuration. Check the GLP dimensions against the manufacturer's specifications and confirm that the adaptor fits the available installation space. The specified rotational speed should be assessed alongside the permitted limits of the adaptor, collet, cutting tool and machine assembly. Follow the equipment instructions for fitting and carry out regular inspections to identify possible wear or damage. The MTM ER Collet Chuck Adaptor SLA10 Type 15000 RPM (GLP: 50 - 160 mm) should be selected according to verified dimensions, connection requirements and the needs of the intended machining application.

Type of Product : ER Collet Chuck Adaptor

ER Type : SLA10

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (7)

Ships within 5 days

MTM ER Collet Chuck Adaptor SLA08 Type 15000 RPM (GLP: 50 - 160 mm)

By MTM

₹3,303 - ₹7,669

You save ₹1,695!

25.49% OFF

The MTM ER Collet Chuck Adaptor SLA08 Type 15000 RPM (GLP: 50 - 160 mm) is a machining accessory intended for compatible tooling systems that use an SLA08-type adaptor configuration. The SLA08 designation distinguishes this version from other adaptor types and helps buyers identify the component required for their machine setup. Its specified rotational speed of 15000 RPM and GLP range of 50–160 mm offer key details for comparing the adaptor with the intended collet chuck assembly, connection requirements and available clearance. For an appropriate fit, confirm the SLA08 interface and machine-side connection against the equipment specifications. Review the GLP dimensions using the manufacturer's documentation before installation, particularly where dimensional clearance affects the setup. The stated speed must be checked against the permitted operating limits of the complete tooling assembly rather than considered in isolation. Ensure that the adaptor is fitted securely and inspect it periodically for wear or damage. The MTM ER Collet Chuck Adaptor SLA08 Type 15000 RPM (GLP: 50 - 160 mm) should be selected after verifying its dimensions and compatibility with the intended machining equipment.

Type of Product : ER Collet Chuck Adaptor

ER Type : SLA08

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (7)

Ships within 5 days

MTM ER Collet Chuck Adaptor SLA06 Type 15000 RPM (GLP: 50 - 160 mm)

By MTM

₹3,421 - ₹7,551

You save ₹1,695!

25.49% OFF

The MTM ER Collet Chuck Adaptor SLA06 Type 15000 RPM (GLP: 50 - 160 mm) is a tooling accessory designed for compatible machining equipment that requires an SLA06-type adaptor connection. Its SLA06 designation helps identify the specific configuration when selecting tooling components for a machine and associated collet chuck arrangement. The stated rotational speed of 15000 RPM and GLP range of 50–160 mm provide useful reference details for assessing dimensional requirements and determining whether the adaptor matches the intended setup. Before selecting the component, verify the SLA06 interface and machine-side connection using the manufacturer's technical documentation. Check the GLP dimensions against the available installation space and requirements of the tooling assembly. The listed rotational speed should be evaluated against the operating limits of the adaptor, collet chuck, cutting tool and machine. Correct fitting and routine inspection can help identify wear or damage before use. The MTM ER Collet Chuck Adaptor SLA06 Type 15000 RPM (GLP: 50 - 160 mm) should be chosen only after confirming its dimensions, connection compatibility and suitability for the intended machining application.

Type of Product : ER Collet Chuck Adaptor

ER Type : SLA06

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (6)

Ships within 5 days

MTM ER Collet Chuck Adaptor SLA32 Type 15000 RPM (GLP: 90 - 200 mm)

By MTM

₹2,949 - ₹9,557

You save ₹959!

24.54% OFF

The MTM ER Collet Chuck Adaptor SLA32 Type 15000 RPM (GLP: 90 - 200 mm) is a tooling component to consider when a machining application calls for an adaptor with the specified SLA32 configuration. Its product designation helps distinguish this variant when comparing adaptor models, reviewing technical specifications, and maintaining tooling inventory records. The stated rotational speed of 15000 RPM and GLP range of 90 - 200 mm provide useful reference points for evaluating the product against the requirements of the intended machine and associated tooling. For correct selection, verify the mounting interface, connection dimensions, and relevant clearances using the machine and adaptor manufacturer's documentation. Confirm the GLP measurement details before comparing this model with other variants. The adaptor must be suitable for the associated collet chuck and the complete tooling arrangement, with the assembled system operating within the limits of every component. Before use, ensure proper installation and check for visible damage, wear, or looseness. Periodic inspection can help identify issues that may affect the suitability of the tooling setup. The MTM ER Collet Chuck Adaptor SLA32 Type 15000 RPM (GLP: 90 - 200 mm) offers defined identification and dimensional details for evaluating its role in a compatible machining arrangement.

Type of Product : ER Collet Chuck Adaptor

ER Type : SLA32

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (6)

Ships within 5 days

MTM ER Collet Chuck Adaptor SLA25 Type 15000 RPM (GLP: 90 - 200 mm)

By MTM

₹2,831 - ₹9,675

You save ₹959!

24.54% OFF

MTM ER Collet Chuck Adaptor SLA25 Type 15000 RPM (GLP: 90 - 200 mm) is a model to evaluate against the application's tooling specifications. Its product designation makes it easier to distinguish this variant from other adaptors in the same range. The stated maximum speed of 15000 RPM and GLP range of 90 - 200 mm provide essential reference information for reviewing dimensions and operating requirements during equipment selection. A careful compatibility check should include the machine-side mounting interface, collet chuck connection, and all relevant dimensional measurements. Confirm the GLP specification and its measurement reference with the manufacturer's documentation before finalizing the selection. In addition, verify that the complete tooling assembly is suitable for the planned speed and machining conditions, since the rating of one component does not establish the limit for the entire system. Follow the appropriate installation procedure and inspect the adaptor regularly for damage, wear, or looseness. The MTM ER Collet Chuck Adaptor SLA25 Type 15000 RPM (GLP: 90 - 200 mm) can support an organized tooling selection process when its listed specifications are matched carefully to the machine and intended operation.

Type of Product : ER Collet Chuck Adaptor

ER Type : SLA25

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (6)

Ships within 5 days

MTM ER Collet Chuck Adaptor SLA20 Type 15000 RPM (GLP: 63 - 200 mm)

By MTM

₹2,595 - ₹9,675

You save ₹959!

24.54% OFF

MTM ER Collet Chuck Adaptor SLA20 Type 15000 RPM (GLP: 63 - 200 mm) provides a clearly identified option within the MTM ER collet chuck adaptor range. The SLA20 designation supports differentiation between product variants, while the specified 15000 RPM operating speed and GLP dimensions of 63 - 200 mm help buyers compare the listed configuration with their tooling requirements. These details are particularly useful when checking product specifications before purchasing or preparing a machine setup. For appropriate selection, compare the adaptor's mounting arrangement and dimensional details with the machine spindle and associated collet chuck. Refer to the manufacturer's documentation to validate the connection type, measurements, and operating conditions rather than assuming compatibility from the model designation alone. The spindle, adaptor, collet chuck, and cutting tool should all be suitable for the intended rotational speed and machining task. During maintenance, inspect the component for visible damage, excessive wear, or signs of an insecure fit. The MTM ER Collet Chuck Adaptor SLA20 Type 15000 RPM (GLP: 63 - 200 mm) offers identifiable specifications that support tooling evaluation and selection when verified against the requirements of the complete assembly.

Type of Product : ER Collet Chuck Adaptor

ER Type : SLA20

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (9)

Ships within 5 days

MTM ER Collet Chuck Adaptor ER50 Type 15000 RPM (GLP: 100 - 160 mm)

By MTM

₹8,613 - ₹15,339

You save ₹5,464!

26.27% OFF

The MTM ER Collet Chuck Adaptor ER50 Type 15000 RPM (GLP: 100 - 160 mm) is a machining tooling component designed for compatible equipment using an ER50 collet chuck arrangement. The ER50 designation helps distinguish this model from smaller ER-type adaptors and supports accurate identification when matching tooling components. With a specified rotational speed of 15000 RPM and a GLP range of 100–160 mm, the product provides key dimensional and operating details for evaluating its suitability for a particular machine and tooling assembly. When choosing the adaptor, confirm the ER50 interface, machine-side connection and collet chuck compatibility against the manufacturer's specifications. The GLP dimensions should be checked against the available space and requirements of the intended installation. The listed speed should not be treated as confirmation that every connected component can safely operate at 15000 RPM; verify the limits of the full assembly. Proper fitting and regular inspection are important for responsible use. The MTM ER Collet Chuck Adaptor ER50 Type 15000 RPM (GLP: 100 - 160 mm) should be selected after its interface, dimensions and operating compatibility have been confirmed.

Type of Product : ER Collet Chuck Adaptor

ER Type : ER50

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (3)

Ships within 5 days

MTM ER Collet Chuck Adaptor ER40 Type 15000 RPM (GLP: 80 - 300 mm)

By MTM

₹2,595 - ₹10,501

You save ₹4,969!

32.12% OFF

The MTM ER Collet Chuck Adaptor ER40 Type 15000 RPM (GLP: 80 - 300 mm) is a tooling accessory intended for machining equipment that supports an ER40 collet chuck configuration. Its ER40 designation identifies the required interface size and helps users select the appropriate adaptor for their tooling arrangement. The stated rotational speed of 15000 RPM and GLP range of 80–300 mm provide important reference specifications when comparing the component with machine requirements, collet compatibility and available installation clearance. Before selecting this adaptor, verify that the ER40 interface matches the intended collet chuck and machine connection. Confirm the GLP dimensions using the manufacturer's technical information and check that the complete assembly meets the equipment's operating requirements. The listed rotational speed must be considered alongside the permitted limits of the adaptor, collet, cutting tool and machine. Secure installation and periodic inspection can help identify wear or damage. The MTM ER Collet Chuck Adaptor ER40 Type 15000 RPM (GLP: 80 - 300 mm) should be selected according to verified dimensions and compatibility with the intended machining setup.

Type of Product : ER Collet Chuck Adaptor

ER Type : ER40

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (12)

Ships within 5 days

MTM ER Collet Chuck Adaptor ER32 Type 15000 RPM (GLP: 70 - 300 mm)

By MTM

₹2,595 - ₹10,501

You save ₹4,969!

32.12% OFF

The MTM ER Collet Chuck Adaptor ER32 Type 15000 RPM (GLP: 70 - 300 mm) is a tooling accessory designed for compatible machining systems using an ER32 collet chuck arrangement. Its ER32 designation helps identify the appropriate adaptor interface when selecting components for a machine and collet assembly. The stated rotational speed of 15000 RPM and GLP range of 70–300 mm provide important selection details for assessing dimensional compatibility and the requirements of the intended tooling setup. Before purchasing, verify the ER32 interface against the collet chuck and machine-side connection specifications. Check the GLP dimensions and available clearance using the manufacturer's technical information. Although 15000 RPM is the listed speed, the actual operating limit must be suitable for the complete assembly, including the adaptor, collet, tool and machine. Ensure correct installation and carry out regular inspections to identify wear, damage or fitting issues. The MTM ER Collet Chuck Adaptor ER32 Type 15000 RPM (GLP: 70 - 300 mm) should be selected after confirming the interface, dimensions and operating requirements of the intended machining application.

Type of Product : ER Collet Chuck Adaptor

ER Type : ER32

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (14)

Ships within 5 days

MTM ER Collet Chuck Adaptor ER25 Type 15000 RPM (GLP: 70 - 300 mm)

By MTM

₹2,595 - ₹11,209

You save ₹4,261!

27.54% OFF

The MTM ER Collet Chuck Adaptor ER25 Type 15000 RPM (GLP: 70 - 300 mm) is a machining tooling component intended for equipment that supports an ER25 collet chuck configuration. The ER25 designation identifies the required interface size, helping users distinguish this adaptor from other variants in the MTM range. Its specified rotational speed of 15000 RPM and GLP range of 70–300 mm offer useful criteria when comparing the component with machine requirements, tooling dimensions and installation clearance. For correct selection, confirm that the ER25 connection is compatible with the intended collet chuck and machine interface. Review the GLP dimensions in the manufacturer's documentation to establish suitability for the planned setup. The listed speed should be checked against the maximum permitted operating speed of every component in the assembled system. Follow the equipment instructions for fitting and inspect the adaptor periodically for damage or wear. The MTM ER Collet Chuck Adaptor ER25 Type 15000 RPM (GLP: 70 - 300 mm) should be matched to verified dimensional specifications and the operating requirements of the intended machining equipment.

Type of Product : ER Collet Chuck Adaptor

ER Type : ER25

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (13)

Ships within 5 days

MTM ER Collet Chuck Adaptor ER20 Type 15000 RPM (GLP: 70 - 300 mm)

By MTM

₹2,949 - ₹7,905

You save ₹3,494!

30.65% OFF

The MTM ER Collet Chuck Adaptor ER20 Type 15000 RPM (GLP: 70 - 300 mm) is a tooling accessory designed for compatible machining equipment that uses an ER20 collet chuck arrangement. Its ER20 designation helps users identify the appropriate adaptor size when matching tooling components to a machine. The specified rotational speed of 15000 RPM and GLP range of 70–300 mm provide key reference details for evaluating the adaptor's dimensional requirements and suitability for the intended machining configuration. Before installation, verify that the ER20 interface matches the collet chuck and that the machine-side connection is compatible with the equipment. Compare the GLP dimensions with the manufacturer's specifications and available clearance in the working setup. The stated rotational speed must be assessed alongside the operating limits of the adaptor, collet, cutting tool and machine. Correct fitting and routine inspection are important for identifying wear or damage before use. The MTM ER Collet Chuck Adaptor ER20 Type 15000 RPM (GLP: 70 - 300 mm) should be selected after confirming dimensional compatibility and the requirements of the intended machining application.

Type of Product : ER Collet Chuck Adaptor

ER Type : ER20

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (11)

Ships within 5 days

MTM ER Collet Chuck Adaptor ER16 Type 15000 RPM (GLP: 70 - 300 mm)

By MTM

₹2,595 - ₹7,905

You save ₹3,494!

30.65% OFF

The MTM ER Collet Chuck Adaptor ER16 Type 15000 RPM (GLP: 70 - 300 mm) is a tooling component intended for compatible machining systems using an ER16 collet chuck arrangement. The ER16 designation helps identify the required interface size and supports accurate selection among the available MTM adaptor variants. With a stated rotational speed of 15000 RPM and a GLP range of 70–300 mm, this model offers specifications that can be checked against the dimensional and operating requirements of the planned tooling configuration. For a suitable match, verify the ER16 interface, machine connection and collet chuck compatibility before purchase. The GLP range should be compared with the manufacturer's dimensional information and the clearance available in the machine setup. Confirm that the selected adaptor and every connected component are approved for the intended operating speed; the stated 15000 RPM should not override any lower component limit. Secure fitting and regular inspection help support responsible tooling maintenance.

Type of Product : ER Collet Chuck Adaptor

ER Type : ER16

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (11)

Ships within 5 days

MTM ER Collet Chuck Adaptor ER11 Type 15000 RPM (GLP: 70 - 150 mm)

By MTM

₹2,949 - ₹4,129

You save ₹1,408!

25.42% OFF

The MTM ER Collet Chuck Adaptor ER11 Type 15000 RPM (GLP: 70 - 150 mm) is a machining accessory designed for tooling setups that require a compatible ER11 collet chuck configuration. Its ER11 designation identifies the collet interface size and helps distinguish this model from other adaptors in the MTM range. The specified rotational speed of 15000 RPM and GLP range of 70–150 mm are important selection details for matching the component to the machine, collet assembly and available installation space. When choosing this adaptor, check the ER11 interface and confirm compatibility with the intended collet chuck and machine-side connection. The GLP dimensions should be verified using the manufacturer's product specifications to ensure an appropriate fit. Although the product is specified for 15000 RPM, the permitted operating speed of the complete tooling assembly must also be considered. Ensure that the adaptor is fitted securely and inspect it periodically for wear or damage.

Type of Product : ER Collet Chuck Adaptor

ER Type : ER11

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (5)

Ships within 5 days

MTM ER Collet Chuck Adaptor FMH27 Type 15000 RPM (GLP: 55 - 300 mm)

By MTM

₹2,359 - ₹14,159

You save ₹4,568!

24.39% OFF

The MTM ER Collet Chuck Adaptor FMH27 Type 15000 RPM (GLP: 55 - 300 mm) is a tooling component designed for machining setups that require a compatible FMH27-type connection. The FMH27 designation distinguishes this configuration from other adaptor variants and supports accurate identification during tooling selection. Its specified rotational speed of 15000 RPM and GLP range of 55–300 mm are key details to review when determining whether the component's dimensions and connection arrangement match the requirements of the intended machine. For correct selection, verify the FMH27 interface and confirm that the machine-side connection matches the equipment documentation. Review the GLP dimensions and ensure that the adaptor fits the planned tooling arrangement without conflicting with the available clearance. The listed speed must be checked against the permitted operating limits of all components in the assembled system. Follow the manufacturer's fitting instructions and inspect the adaptor periodically for signs of wear or damage. The MTM ER Collet Chuck Adaptor FMH27 Type 15000 RPM (GLP: 55 - 300 mm) should be selected based on verified specifications and compatibility with the intended machining application.

Type of Product : ER Collet Chuck Adaptor

ER Type : FMH27

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (14)

Ships within 5 days

MTM ER Collet Chuck Adaptor FMH22 Type 15000 RPM (GLP: 50 - 350 mm)

By MTM

₹2,359 - ₹11,209

You save ₹4,261!

27.54% OFF

The MTM ER Collet Chuck Adaptor FMH22 Type 15000 RPM (GLP: 50 - 350 mm) is a machining accessory intended for compatible tooling arrangements that require an FMH22-type adaptor connection. Its FMH22 designation helps identify the specified configuration when selecting components for a machine and collet chuck assembly. The listed rotational speed of 15000 RPM and GLP range of 50–350 mm provide useful reference details for comparing the adaptor with the machine's connection requirements and the dimensional constraints of the intended setup. Before selecting this component, confirm the FMH22 interface and machine-side connection using the manufacturer's technical documentation. Check the GLP range against the required dimensions and available clearance. The stated rotational speed should be assessed alongside the maximum permitted speed of the adaptor, collet, cutting tool and machine assembly. Proper fitment and periodic inspection are important for identifying wear or damage before use. The MTM ER Collet Chuck Adaptor FMH22 Type 15000 RPM (GLP: 50 - 350 mm) should be chosen only after confirming its dimensional specifications and compatibility with the intended machining equipment.

Type of Product : ER Collet Chuck Adaptor

ER Type : FMH22

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (14)

Ships within 5 days

MTM ER Collet Chuck Adaptor FMH16 Type 15000 RPM (GLP: 40 - 300 mm)

By MTM

₹2,359 - ₹7,669

You save ₹3,635!

32.16% OFF

The MTM ER Collet Chuck Adaptor FMH16 Type 15000 RPM (GLP: 40 - 300 mm) is a tooling accessory intended for machining arrangements that require a compatible FMH16-type connection. Its FMH16 designation helps identify the specified adaptor configuration when comparing tooling options for a particular machine. The product is listed with a rotational speed of 15000 RPM and a GLP range of 40–300 mm, providing useful reference details for checking dimensions and compatibility with the planned machining setup. Before purchase, verify the precise FMH16 interface and machine-side connection using the manufacturer's product documentation. Confirm that the GLP dimensions suit the intended installation and that the adaptor is compatible with the associated collet chuck and tooling components. The stated rotational speed must be checked against the permitted operating limits of the entire assembly, rather than considered in isolation. Correct installation and regular inspection can help identify damage or wear that may affect suitability. The MTM ER Collet Chuck Adaptor FMH16 Type 15000 RPM (GLP: 40 - 300 mm) should be selected only after confirming the connection type, dimensional requirements and operating specifications for the intended equipment.

Type of Product : ER Collet Chuck Adaptor

ER Type : FMH16

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (11)

Ships within 5 days

MTM ER Collet Chuck Adaptor FMH40 Type 15000 RPM (GLP: 70 - 300 mm)

By MTM

₹3,067 - ₹11,563

You save ₹2,219!

27.34% OFF

The MTM ER Collet Chuck Adaptor FMH40 Type 15000 RPM (GLP: 70 - 300 mm) is a tooling accessory intended for compatible machining systems requiring an FMH40-type adaptor connection. The FMH40 designation helps distinguish this configuration from other adaptor types and supports accurate component selection when matching tooling to a machine. Its specified rotational speed of 15000 RPM and GLP range of 70–300 mm provide important reference details for assessing the dimensional requirements and compatibility of the planned assembly. Before purchasing, verify the FMH40 connection and machine-side interface against the manufacturer's technical specifications. Check the GLP dimensions against the required installation space and the associated tooling configuration. The stated rotational speed should be evaluated against the permitted operating limits of the adaptor, collet chuck, cutting tool and machine. Correct installation and regular inspection can help identify wear, damage or fitting issues before operation. The MTM ER Collet Chuck Adaptor FMH40 Type 15000 RPM (GLP: 70 - 300 mm) should be selected after confirming the connection type, dimensions and suitability for the intended machining setup.

Type of Product : ER Collet Chuck Adaptor

ER Type : FMH40

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (12)

Ships within 5 days

MTM ER Collet Chuck Adaptor FMH32 Type 15000 RPM (GLP: 60 - 300 mm)

By MTM

₹2,949 - ₹14,159

You save ₹3,034!

28.66% OFF

The MTM ER Collet Chuck Adaptor FMH32 Type 15000 RPM (GLP: 60 - 300 mm) is a machining tooling accessory intended for compatible equipment using an FMH32-type adaptor arrangement. Its designated type helps users identify the required connection configuration when comparing components for a particular machine and collet chuck setup. The product specifies a rotational speed of 15000 RPM and a GLP range of 60–300 mm, giving buyers important reference information for checking the adaptor against the dimensional requirements of their tooling system. Before installation, confirm the exact FMH32 interface and machine-side connection with the manufacturer's documentation. Compare the GLP dimensions with the intended setup and available clearance to ensure a suitable match. The stated rotational speed should be reviewed against the operating limits of the adaptor and every connected component, including the machine and cutting tool. Secure installation and routine inspection help identify potential wear or damage. The MTM ER Collet Chuck Adaptor FMH32 Type 15000 RPM (GLP: 60 - 300 mm) should be chosen after confirming its dimensions, connection compatibility and suitability for the intended machining operation.

Type of Product : ER Collet Chuck Adaptor

ER Type : FMH32

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (13)

Ships within 5 days

MTM BT50 ER11 ER Collet Chuck Adaptor (GPL: 63 - 125 mm)

By MTM

₹5,781 - ₹10,737

You save ₹4,957!

31.59% OFF

The MTM BT50 ER11 ER Collet Chuck Adaptor (GPL: 63 - 125 mm) is a machining tool accessory designed for tooling setups that require a BT50 mounting configuration and an ER11 collet chuck interface. These designations help identify the adaptor's intended connection arrangement when selecting components for compatible milling equipment. The specified GPL range of 63 - 125 mm provides an additional dimensional reference for comparing the adaptor with the machine setup and tool access requirements. Reviewing these details before purchase can help ensure that the selected configuration matches the intended application. Before installation, verify the BT50 spindle interface, ER11 collet compatibility, overall dimensions, and relevant clearances using the manufacturer's technical documentation. Confirm the GPL measurement reference to ensure that the stated range is interpreted correctly. The adaptor, collet, cutting tool, and spindle should be suitable for the planned machining operation and its operating conditions. Proper fitting and secure retention are essential before starting the machine. Routine inspection can help identify wear, damage, or looseness that may affect the tooling arrangement. The MTM BT50 ER11 ER Collet Chuck Adaptor (GPL: 63 - 125 mm) can be evaluated for compatible machining applications where its mounting configuration and dimensional specifications meet the equipment requirements.

Type of Product : ER Collet Chuck Adaptor

Balancing : 15000 RPM

Tempring : 0.005mm

Taper Type : BT50

Explore other Variants (2)

Ships within 5 days

MTM ER Collet Chuck Adaptor SLA40 Type 15000 RPM (GLP: 115 - 160 mm)

By MTM

₹3,067 - ₹7,905

You save ₹3,494!

30.65% OFF

MTM ER Collet Chuck Adaptor SLA40 Type 15000 RPM (GLP: 115 - 160 mm) provides a clearly specified option for technical evaluation. The model name identifies its configuration within the MTM ER collet chuck adaptor range, making it easier to distinguish during product comparison and tooling procurement. Its listed rotational speed of 15000 RPM and GLP range of 115 - 160 mm are important reference specifications when determining whether the adaptor corresponds to the intended machining setup. Before purchasing or installing the adaptor, check its mounting dimensions and connection requirements against the machine spindle and compatible collet chuck documentation. The stated GLP range should be interpreted according to the manufacturer's measurement reference to avoid selection errors. Confirm that all components in the assembled tooling system are suitable for the planned operating speed and machining conditions. Correct installation, secure retention, and regular inspection should form part of routine tooling checks. Look for signs of wear, damage, or an unsuitable fit before operation. The MTM ER Collet Chuck Adaptor SLA40 Type 15000 RPM (GLP: 115 - 160 mm) can be assessed for a machining application once its specifications and interface compatibility have been verified.

Type of Product : ER Collet Chuck Adaptor

ER Type : SLA40

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (3)

Ships within 5 days

MTM Baby Collet Chuck Adaptor ER08 ER Type 15000 RPM (GLP: 100 - 150 mm)

By MTM

₹2,831 - ₹3,421

You save ₹1,110!

24.5% OFF

The MTM Baby Collet Chuck Adaptor ER08 ER Type 15000 RPM (GLP: 100 - 150 mm) is a tooling accessory designed for compatible machining setups that use an ER08 collet chuck arrangement. Its ER type designation helps identify the required adaptor configuration when selecting tooling components for a particular machine. The specified rotational speed of 15000 RPM and GLP range of 100–150 mm are key details to consider when comparing this product with the machine's requirements and the intended machining setup. Before selecting the adaptor, verify the ER08 interface, machine-side connection, dimensional requirements and compatibility with the intended collet chuck assembly. The stated speed should be checked against the manufacturer's operating specifications and the complete tool assembly's permitted limits. Correct fitment and secure installation are important for reliable operation, while routine inspection can help identify wear or damage before use.

Type of Product : Baby Collet Chuck Adaptor

ER Type : ER08

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (5)

Ships within 5 days

MTM Baby Collet Chuck Adaptor ER11 ER Type 15000 RPM (GLP: 100 - 150 mm)

By MTM

₹2,831 - ₹3,421

You save ₹945!

25.03% OFF

The MTM Baby Collet Chuck Adaptor ER11 ER Type 15000 RPM (GLP: 100 - 150 mm) is a machining accessory intended for compatible tooling arrangements using an ER11 collet chuck configuration. The ER11 designation distinguishes this version from other collet adaptor sizes and helps buyers identify the required interface when organizing machining tools. With a specified rotational speed of 15000 RPM and a GLP range of 100–150 mm, this model provides defined selection details for checking its suitability against the equipment and application. When choosing the adaptor, confirm that the ER11 connection matches the intended collet chuck and that the machine-side interface meets the equipment specifications. The stated speed must also be evaluated against the permitted operating limits of the adaptor, collet, tool and machine assembly. Check the dimensions and fitting requirements before installation, and inspect the component for wear or damage during routine maintenance.

Type of Product : Baby Collet Chuck Adaptor

ER Type : ER11

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (5)

Ships within 5 days

MTM Baby Collet Chuck Adaptor ER40 ER Type 15000 RPM (GLP: 85 - 150 mm)

By MTM

₹3,539 - ₹4,011

You save ₹1,405!

25.94% OFF

The MTM Baby Collet Chuck Adaptor ER40 ER Type 15000 RPM (GLP: 85 - 150 mm) is a tooling accessory intended for compatible machining equipment that uses an ER40 collet chuck arrangement. The ER40 designation helps identify the required adaptor size when selecting tooling components for a specific machine configuration. Its stated rotational speed of 15000 RPM and GLP range of 85–150 mm provide useful reference details for evaluating dimensional suitability and compatibility with the intended tooling assembly. Before selecting this adaptor, confirm that the ER40 interface matches the collet chuck and that the machine-side connection meets the equipment requirements. Verify the GLP dimensions against the manufacturer's specifications and ensure adequate clearance within the planned setup. The specified rotational speed must be checked against the permitted limits of the adaptor, collet, cutting tool and machine assembly.

Type of Product : Baby Collet Chuck Adaptor

ER Type : ER40

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (5)

Ships within 5 days

MTM Baby Collet Chuck Adaptor ER32 ER Type 15000 RPM (GLP: 65 - 150 mm)

By MTM

₹3,539 - ₹4,011

You save ₹1,299!

24.46% OFF

The MTM Baby Collet Chuck Adaptor ER32 ER Type 15000 RPM (GLP: 65 - 150 mm) is a tooling accessory designed for compatible machining systems using an ER32 collet chuck arrangement. The ER32 designation identifies the adaptor size, helping users select the appropriate component for their intended tooling configuration. Its stated rotational speed of 15000 RPM and GLP range of 65–150 mm are relevant specifications for comparing the adaptor with the machine connection, available clearance and dimensional requirements of the planned setup. Prior to installation, verify the ER32 interface and confirm that the adaptor matches the collet chuck and machine-side connection. Review the GLP dimensions using the manufacturer's technical documentation, particularly where clearance and tool positioning are important. The stated speed should be considered alongside the maximum permitted operating speed of every component in the assembled system. Secure fitting and regular inspection are essential parts of responsible tooling maintenance.

Type of Product : Baby Collet Chuck Adaptor

ER Type : ER32

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (9)

Ships within 5 days

MTM Baby Collet Chuck Adaptor ER25 ER Type 15000 RPM (GLP: 60 - 150 mm)

By MTM

₹3,421 - ₹3,775

You save ₹1,299!

25.6% OFF

The MTM Baby Collet Chuck Adaptor ER25 ER Type 15000 RPM (GLP: 60 - 150 mm) is a machining tooling component intended for equipment that supports an ER25 collet chuck configuration. Its ER25 designation provides a clear identifier for selecting the required adaptor size and differentiating it from other variants. With a specified rotational speed of 15000 RPM and a GLP range of 60–150 mm, the product offers key details for evaluating its suitability for a planned tooling arrangement and the dimensional requirements of the machine. For correct selection, check the ER25 connection against the compatible collet chuck and machine interface. The GLP range should be verified with the manufacturer's dimensional information before the adaptor is fitted. The listed speed is a selection reference and must be checked against the permitted operating limits of the adaptor, collet, cutting tool and machine. Inspect the component regularly and ensure it is installed securely according to the equipment instructions

Type of Product : Baby Collet Chuck Adaptor

ER Type : ER25

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (12)

Ships within 5 days

MTM Baby Collet Chuck Adaptor ER20 ER Type 15000 RPM (GLP: 60 - 150 mm)

By MTM

₹2,713 - ₹3,421

You save ₹1,110!

24.5% OFF

The MTM Baby Collet Chuck Adaptor ER20 ER Type 15000 RPM (GLP: 60 - 150 mm) is a tooling accessory designed for machining setups that require a compatible ER20 collet chuck arrangement. The ER20 designation helps identify the adaptor configuration and distinguish it from other sizes available in the MTM range. Its specified rotational speed of 15000 RPM and GLP range of 60–150 mm provide important reference details when assessing the component for a particular machine, tool assembly and machining requirement. Before purchasing, confirm that the ER20 interface matches the intended collet chuck and that the machine-side connection is suitable for the equipment. Check the GLP dimensions against the manufacturer's specifications to ensure the required fit and clearance. The stated rotational speed should also be assessed against the operating limits of the complete assembled tooling system. Proper installation and periodic inspection can help identify wear, damage or fitting issues.

Type of Product : Baby Collet Chuck Adaptor

ER Type : ER20

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (5)

Ships within 5 days

MTM Baby Collet Chuck Adaptor ER16 ER Type 15000 RPM (GLP: 100 - 150 mm)

By MTM

₹2,831 - ₹3,421

You save ₹1,110!

24.5% OFF

The MTM Baby Collet Chuck Adaptor ER16 ER Type 15000 RPM (GLP: 100 - 150 mm) is a tooling component intended for machining equipment that supports a compatible ER16 collet chuck arrangement. Its ER16 designation identifies the adaptor size and helps distinguish it from other variants within the MTM range. The specified rotational speed of 15000 RPM and GLP range of 100–150 mm provide important product details for assessing the component against the requirements of the machine, collet assembly and planned tooling application. Before use, verify the ER16 interface and ensure that the adaptor matches the machine connection and the intended collet chuck. Confirm the meaning and dimensional requirements of the GLP specification against the manufacturer's product information. The listed speed should not exceed the permitted limit of any component in the assembled tooling system. Correct installation, secure fitting and regular inspection are important considerations in machining operations.

Type of Product : Baby Collet Chuck Adaptor

ER Type : ER16

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (4)

Ships within 5 days

MTM ER Collet Chuck Adaptor MTA05 Type 15000 RPM (GLP: 120 - 220 mm)

By MTM

₹4,719 - ₹6,489

You save ₹2,550!

28.21% OFF

The MTM ER Collet Chuck Adaptor MTA05 Type 15000 RPM (GLP: 120 - 220 mm) is a tooling accessory intended for machining systems that support a compatible MTA05-type connection. Its designated type helps identify the required adaptor configuration when selecting components for a particular machine and tooling assembly. The specified rotational speed of 15000 RPM and GLP range of 120–220 mm are useful selection references for assessing the adaptor's dimensional suitability and compatibility with the planned installation. To choose the correct component, verify the MTA05 interface and machine-side connection against the manufacturer's specifications. Check the GLP range against the required dimensions and available clearance in the tooling setup. The listed rotational speed should be considered alongside the permitted limits of the adaptor, collet chuck, cutting tool and machine as a complete assembly. Follow the equipment instructions when fitting the adaptor and inspect it periodically for damage or wear. The MTM ER Collet Chuck Adaptor MTA05 Type 15000 RPM (GLP: 120 - 220 mm) should be selected after confirming its connection requirements, dimensional fit and suitability for the intended machining equipment.

Type of Product : ER Collet Chuck Adaptor

ER Type : MTA05

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (2)

Ships within 5 days

MTM ER Collet Chuck Adaptor MTA04 Type 15000 RPM (GLP: 95 - 180 mm)

By MTM

₹2,713 - ₹4,955

You save ₹1,752!

26.12% OFF

The MTM ER Collet Chuck Adaptor MTA04 Type 15000 RPM (GLP: 95 - 180 mm) is a machining tooling component intended for compatible equipment using an MTA04-type adaptor configuration. The MTA04 designation helps distinguish this version from other connection types within the MTM range and supports accurate selection during tooling preparation. Its listed rotational speed of 15000 RPM and GLP range of 95–180 mm provide key details for comparing the adaptor with the dimensional and operating requirements of the intended machine assembly. Before installation, check the MTA04 interface against the machine-side connection and confirm compatibility with the intended collet chuck or tooling arrangement. Verify the GLP dimensions using the manufacturer's technical documentation and ensure that the adaptor suits the available installation space. The specified speed must be assessed against the operating limits of every component in the assembled system. Secure installation and periodic inspection can help identify wear, damage or fitting concerns. The MTM ER Collet Chuck Adaptor MTA04 Type 15000 RPM (GLP: 95 - 180 mm) should be chosen according to verified specifications and the needs of the intended machining operation.

Type of Product : ER Collet Chuck Adaptor

ER Type : MTA04

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (3)

Ships within 5 days

MTM ER Collet Chuck Adaptor MTA03 Type 15000 RPM (GLP: 65 - 150 mm)

By MTM

₹2,359 - ₹4,719

You save ₹1,828!

27.92% OFF

The MTM ER Collet Chuck Adaptor MTA03 Type 15000 RPM (GLP: 65 - 150 mm) is a tooling accessory designed for compatible machining arrangements that require an MTA03-type adaptor connection. Its model designation helps identify the required configuration when matching tooling components to the machine and collet chuck assembly. The specified rotational speed of 15000 RPM and GLP range of 65–150 mm provide useful reference details for evaluating the adaptor's dimensional requirements and suitability for the planned machining setup. When choosing this component, confirm that the MTA03 interface matches the intended machine connection and associated tooling. Compare the GLP dimensions with the manufacturer's specifications and the clearance available in the installation. The stated rotational speed should be checked against the maximum permitted speed of the complete assembly, including the adaptor, collet, cutting tool and machine. Follow the equipment instructions for correct fitting and inspect the component regularly for wear or damage. The MTM ER Collet Chuck Adaptor MTA03 Type 15000 RPM (GLP: 65 - 150 mm) should be selected after verifying its connection type, dimensions and compatibility with the intended application.

Type of Product : ER Collet Chuck Adaptor

ER Type : MTA03

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (5)

Ships within 5 days

MTM ER Collet Chuck Adaptor MTA02 Type 15000 RPM (GLP: 60 - 140 mm)

By MTM

₹2,241 - ₹4,483

You save ₹1,530!

25.45% OFF

The MTM ER Collet Chuck Adaptor MTA02 Type 15000 RPM (GLP: 60 - 140 mm) is a tooling component intended for compatible machining equipment that uses an MTA02-type adaptor arrangement. The MTA02 designation provides a specific identifier for this configuration, helping buyers distinguish it from other adaptors in the MTM range. Its stated rotational speed of 15000 RPM and GLP range of 60–140 mm are important specifications for comparing the adaptor with the connection requirements and dimensional constraints of the intended machine setup. Before selection, verify the MTA02 interface and confirm that it is compatible with the machine-side connection and associated collet chuck assembly. Review the GLP dimensions against the manufacturer's product information to establish whether the component suits the required installation space. The listed speed should be assessed against the operating limits of the complete tooling system, including the adaptor, collet, tool and machine. Secure fitting and routine inspection are important for responsible operation. The MTM ER Collet Chuck Adaptor MTA02 Type 15000 RPM (GLP: 60 - 140 mm) should be selected only after its dimensions and compatibility with the intended machining equipment have been confirmed.

Type of Product : ER Collet Chuck Adaptor

ER Type : MTA02

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (5)

Ships within 5 days

MTM ER Collet Chuck Adaptor MTA01 Type 15000 RPM (GLP: 45 - 120 mm)

By MTM

₹2,241 - ₹4,483

You save ₹1,615!

26.49% OFF

The MTM ER Collet Chuck Adaptor MTA01 Type 15000 RPM (GLP: 45 - 120 mm) is a machining accessory designed for tooling arrangements that require a compatible MTA01-type connection. Its type designation helps identify the specific adaptor configuration when reviewing components for a machine and collet chuck assembly. With a listed rotational speed of 15000 RPM and a GLP range of 45–120 mm, this model offers useful selection details for evaluating its dimensional suitability and compatibility with the intended equipment. To ensure a suitable match, confirm the MTA01 interface and machine-side connection using the manufacturer's documentation. Verify that the GLP dimensions meet the installation requirements and allow the necessary clearance within the tooling setup. The specified rotational speed must be checked against the maximum permitted operating speed of all connected components. Follow the relevant fitting instructions and inspect the adaptor for wear or damage as part of routine maintenance. The MTM ER Collet Chuck Adaptor MTA01 Type 15000 RPM (GLP: 45 - 120 mm) should be chosen according to verified dimensions, connection requirements and machine compatibility.

Type of Product : ER Collet Chuck Adaptor

ER Type : MTA01

Balancing : 15000 RPM

Tempring : 0.005mm

Explore other Variants (5)

Previous Next

Page 1 of 1 results