Ships within 19 days
View
View
View
View
| Type of Product | Speedometer |
| Country of Origin | Japan |
| Name of Manufacturer/Packer/Importer | COCO RESEARCH |
| Model No | TDP-4921-ECDF |
Type of Product |
Speedometer |
Country of Origin |
Japan |
Name of Manufacturer/Packer/Importer |
COCO RESEARCH |
Model No |
TDP-4921-ECDF |
Monotaro ID |
66273028 |
Input Method |
Single-phase/two-phase signal, 1- Single-phase signal trigger direction, falling edge 2- UP/DOWN signal trigger direction, falling edge 3- A/B phase signal trigger direction, falling edge/rising edge 4- Direction signal speed input trigger direction, falling edge direction input trigger direction, falling edge/rising edge set in program mode |
Storage Temperature Range |
-20 to +70 ℃ |
Operation Mode |
Comparator output: Isolated non-contact output (photoMOS relay) |
Input Power |
DC 9.6-30 V |
Measurement Resolution |
26 ns |
Number of Input Points |
1point |
Function |
Scaling: Latematic™ |
Specifications |
●Analog: 0-10V●Comparator output/ON resistance, update time, output hold function, response time, output connector: 50Ω or less, selectable display update time/synchronized with analog output update time, comparator reset function, 3ms (max), terminal block 7.62mm pitch M3 free terminal●Comparator output section/number of outputs, number of setting digits, polarity setting: 2 points (HIGH, LOW), 6 digits (HIGH, LOW), 0=+, 1=- *Set in program mode●Serial output: 2 extended comparators●Sensor power output: +12V±10%, 150mA max●Dynamic prediction™: 9 levels (including continuous prediction and periodic hold)●Extended comparator output/output type, ON resistance, response time, output connector: isolated non-contact output (photoMOS relay), 50Ω or less, 3ms (max), terminal block 7.62mm pitch M3 Free terminal screws. ●Extended comparator output section: Number of output points, number of setting digits, polarity setting, decimal point position: 2 points (COMP1, COMP2), 6 digits (COMP1, COMP2), 0 = +, 1 = - (Set in program mode), same as standard HIGH comparator value. ●Extended comparator output section: Setting method: Set in program mode. ● Update time (m): 0.5 ● Setting value storage: Non-volatile memory (EEPROM). ● Measurement mode: Calculation rate: Frequency meter mode, Period meter mode / Sets the display value relative to the input frequency. Input frequency rate: 0.00001 - 999999 (Hz) / Display rate 0.00001 - 999999. ● Input connector terminal block: 7.62 mm pitch M3 free terminal screws. ● Input pulse width: H and L levels must be 100 ns or more. ● Input signal/input circuit/input withstand voltage: Logic signal / +5V pull-up at approximately 5 kΩ. +30V/-25V●Input voltage resistance/Input connector: ±30V/Terminal block 7.62mm pitch M3 free terminal screw●Display update time/Display accuracy: 0.1 to 99.9 seconds (can be set in 0.1 second increments in program mode)/5 ppm ±1 digit @ 23°C●Display range/Polarity display/Over display/Zero display: -199999 to 999999/When rotating in reverse, "-" lights up/OL display/Leading zero suppression |
Operating Temperature / Humidity Range |
0℃ to +40℃/85%RH or less (no condensation) |
Tip Shape |
Input: Input from rear terminal (short circuit with GND terminal) |
Input Signal |
1. Logic input Input level: H level 4V or more, L level 1V or less 2. Zero cross input AC signal with input sensitivity of ±40mV or more |
Power Consumption (VA) |
8 or less |
Atmosphere |
Surrounding area: No corrosive gases |
Import Country |
Direct Import from Japan |
Display |
Numerical display/6 digits: 7-segment LED, character height 14.2mm |
Rating |
Comparator output: DC350V 80mA max (resistive load) AC240V 80mA max (resistive load) |
Pattern Setting |
Comparator output: Set in program mode, push switch |
Input Frequency (Hz) |
0.0006 to 4M (single phase signal) / 0.0006 to 1M (A/B phase signal) |
Looking for bulk pricing or different specifications?
Subscribe to Newsletter
Sign up to get exclusive offers from our favorite brands and to be well up in the news
