Avr Products Online

A general purpose 40 pin AVR development board with onboard USB support, 16x2 LCD support, power supply circuit, RS232 port for serial interface with computer and other serial devices, reset switch, power status LED, a 6 pin ISP header and 4 x general purpose LEDs and Switches.The board provides port extensions for all ports and also provides an empty hole for each IO pin, where wires and connectors can be soldered directly for further expansion.
The board features an onboard USB to Serial converter which can be used to do serial communication between the microcontroller and the computer over the USB port. This greatly increases the easy with which the board can connect and communicate with computers.
The board is compatible with the Atmega16, Atmega32 and other compatible 40 pin AVR microcontrollers. Use this board to kick start development based on compatible 8051 microcontrollers. The board lets concentrate on programming, testing and optimizing code, and thereby overal project, rather than spending time in getting to know the electronics required to use these microcontrollers. These boards are perfect for learning, testing and development.
The Intermediate Board offers support for 16x2 LCDs with onboard contrast control and it offers a lot more general purpose LEDs and Switches than basic boards (4 x general purpose LEDs and Switches). The LEDs and Switches are connected to the IO pins on the microcontroller through jumpers and their connection to the pins can be disabled if wish to use the IO pin for other purposes.
can use AVR USB Programmer for programing this board.
Features
The board is built upon high quality FR-4(1.5 mm) with a green solder mask and a clear and legible white legend. All IO pins are labelled with their names along with any dual feature they support. This greatly simplifies prototyping.
Onboard 16x2 LCD support with contrast control
Onboard USB to Serial converter for serial communication and programming over USB
Onboard MAX232 interface circuit for easy communication with a computer and other serial devices(GPS modules, GSM Modems, etc).
DC plug-in jack for power input.
Onboard bridge rectifier enables the board to accept both AC and DC input voltages.
Onboard 5V regulator(LM7805) with filtering capacitors and heatsink.
Power Status LED(Green) and a general purpose LED(Red) connected to PB0.
The AVCC pin is connected to 5V through a 100 uH inductor for accurate ADC conversions.
Power Status LED(Green) and 4 x general purpose user LED(Red) and Switches
16 MHz Quartz crystal oscillator circuit.
Port extensions for all ports with detailed pin labeling for easy identification of pins
Vin, 5V and Gnd bus provided.
The board has 4 holes of 3mm diameter for easy mounting.
The package includes a CD and product manual.
The in

This is development board for Atmel's Atmega32u4 microcontroller. It comes with a 8-bit AVR core, 32KB of self-programming flash program memory, 2.5KB SRAM, 1KB EEPROM and a 12-channel 10-bit A/D-converter. It has on-chip USB 2.0. It comes with the factory DFU Bootloader which can be used to program the board using Atmels's FLIP software, without the need for an external programmer.
The board provides port extensions for all ports and also provides an empty hole for each IO pin, where wires and connectors can be soldered directly for further expansion.All pins are clearly labelled to ease prototyping.
The board comes with 4 x General Purpose Switches and LEDs(which can be enabled or disabled as required), a 16 MHZ Quartz crystal circuit, 5V power regulator and a 2x3 ISP header.
Features
The board is built upon high quality FR-4(1.5 mm) with a green solder mask and a clear and legible white legend. All IO pins are labelled with their names. This greatly simplifies prototyping.
Comes with Atmel's DFU Bootloader, and can be programmed through USB with no external programmers required.
DC plug-in jack for power input(7-15V AC/DC).
Onboard bridge rectifier enables the board to accept both AC and DC input voltages.
Onboard 5V Low Dropout Regulator regulator with filtering circuit
Power Status LED(Green) and 4 x general purpose LEDs(Red)
16 MHz Quartz crystal oscillator circuit.
Port extensions for all ports with detailed pin labeling for easy identification of pins
Vin, 5V and Gnd bus provided.
The board has 4 holes of 3mm diameter for easy mounting.
The package includes a CD and product manual.
The included CD contains the board circuit, sample codes, demo projects and tutorials to get started.
This product comes with a warranty and guaranteed aftersales support (subjected to conditions).
Please Note: Product may differ (eg. colour) from the product Image displayed on website. Kindly check the technical specifications provided in description to make better purchase decision.

A general purpose 40 pin AVR evaluation board compatible with the Atmega16 and the Atmega32 microcontrollers. Comes with on board crystal, reset switch, power status LED.This board is perfect for building rapid prototypes and projects using the Atmega16 and Atmega32 microcontrollers. The board provides port extensions for all ports and also provides an empty hole for each IO, where wires and connectors can be soldered directly for further expansion. The board features a DC Jack, which can be used to directly power the board from 5V SMPS Power Supply.
The board is built on a high quality FR-4(1.6 mm) board with a green solder mask and a clear and legible white legend. All I/O pins are labelled with their names along with any dual feature they support. This greatly simplifies prototyping.
Input Voltage: 2.7 - 5.5V (depending on the microcontroller used)
Power Status LED(Green) along with a general purpose LED connected to PB0
Appropriate filtering circuits for ADC power pins for accurate ADC conversions
Standard 6x1 ISP header for programming
Onboard reset switch
Onboard quartz crystal 16 MHz oscillator circuit
Port extensions for all ports
Compatible with Atmel’s Atmega16, Atmega32 and other compatible 40 pin AVR devices
Please Note: Product may differ (eg. col) from the product Image displayed on website. Kindly check the technical specifications provided in description to make better purchase decision.

A general purpose 40 pin AVR development board with 16x2 LCD support, power supply circuit, RS232 port for serial interface with computer and other serial devices, reset switch, power status LED, a 6 pin ISP header and 4 x general purpose LEDs and Switches.The board provides port extensions for all ports and also provides an empty hole for each IO pin, where wires and connectors can be soldered directly for further expansion.
The board is compatible with the Atmega16, Atmega32 and other compatible 40 pin AVR microcontrollers. Use this board to kick start development based on compatible 8051 microcontrollers. The board lets concentrate on programming, testing and optimizing code, and thereby overal project, rather than spending time in getting to know the electronics required to use these microcontrollers. These boards are perfect for learning, testing and development.
The Intermediate Board offers support for 16x2 LCDs with onboard contrast control and it offers a lot more general purpose LEDs and Switches than basic boards (4 x general purpose LEDs and Switches). The LEDs and Switches are connected to the IO pins on the microcontroller through jumpers and their connection to the pins can be disabled if wish to use the IO pin for other purposes.
can use AVR USB Programmer for programing this board.
Features
The board is built upon high quality FR-4(1.5 mm) with a green solder mask and a clear and legible white legend. All IO pins are labelled with their names along with any dual feature they support. This greatly simplifies prototyping.
Onboard 16x2 LCD support with contrast control
Onboard MAX232 interface circuit for easy communication with a computer and other serial devices(GPS modules, GSM Modems, etc).
DC plug-in jack for power input.
Onboard bridge rectifier enables the board to accept both AC and DC input voltages.
Onboard 5V regulator(LM7805) with filtering capacitors and heatsink.
Power Status LED(Green) and a general purpose LED(Red) connected to PB0.
The AVCC pin is connected to 5V through a 100 uH inductor for accurate ADC conversions.
Power Status LED(Green) and 4 x general purpose user LED(Red) and Switches
16 MHz Quartz crystal oscillator circuit.
Port extensions for all ports with detailed pin labeling for easy identification of pins
Vin, 5V and Gnd bus provided.
The board has 4 holes of 3mm diameter for easy mounting.
The package includes a CD and product manual.
The included CD contains the board circuit, sample codes, demo projects and tutorials to get started.
This product comes with a warranty and guaranteed aftersales support (subjected to conditions).
Please Note: Product may differ (eg. col) from the product Image displayed on website. Kindly check the technical specifications provided in description to make be

A general purpose 40 pin AVR development board with on board power supply circuit, RS232 port for serial interface with computer and other serial devices, reset switch, power status LED, a 6 pin ISP header and a general purpose LED and Switch.
The board is compatible with the Atmega16, Atmega32 and other compatible 40 pin AVR microcontrollers. This board is perfect if are just starting out with AVR programming and also if want a tried and tested board for building advanced projects based on it.
can use AVR USB Programmer for programing this board.
Features
The board is built upon high quality FR-4(1.5 mm) with a green solder mask and a clear and legible white legend.
Onboard MAX232 interface circuit for easy communication with a computer and other serial devices(GPS modules, GSM Modems, etc).
DC plug-in jack for power input.
Onboard bridge rectifier enables the board to accept both AC and DC input voltages.
Onboard 5V regulator(LM7805) with filtering capacitors and heatsink.
Power Status LED(Green) and a general purpose LED(Red) connected to PB0.
The AVCC pin is connected to 5V through a 100 uH inductor for accurate ADC conversions.
16 MHz Quartz crystal oscillator circuit.
Port extensions for all ports.
Vin, 5V and Gnd bus provided.
The board has 4 holes of 3mm diameter for easy mounting.
The package includes a CD and product manual.
The included CD contains the board circuit, sample codes, demo projects and tutorials to get started.
This product comes with a warranty and guaranteed aftersales support (subjected to conditions).
Please Note: Product may differ (eg. col) from the product Image displayed on website. Kindly check the technical specifications provided in description to make better purchase decision.

A general purpose 40 pin AVR development board with onboard USB support, 16x2 LCD support, power supply circuit, RS232 port for serial interface with computer and other serial devices, reset switch, power status LED, a 6 pin ISP header and 4 x general purpose LEDs and Switches.The board provides port extensions for all ports and also provides an empty hole for each IO pin, where wires and connectors can be soldered directly for further expansion.
The board features an onboard USB to Serial converter which can be used to do serial communication between the microcontroller and the computer over the USB port. This greatly increases the easy with which the board can connect and communicate with computers.
The board is compatible with the Atmega16, Atmega32 and other compatible 40 pin AVR microcontrollers. Use this board to kick start development based on compatible 8051 microcontrollers. The board lets concentrate on programming, testing and optimizing code, and thereby overal project, rather than spending time in getting to know the electronics required to use these microcontrollers. These boards are perfect for learning, testing and development.
The Intermediate Board offers support for 16x2 LCDs with onboard contrast control and it offers a lot more general purpose LEDs and Switches than basic boards (4 x general purpose LEDs and Switches). The LEDs and Switches are connected to the IO pins on the microcontroller through jumpers and their connection to the pins can be disabled if wish to use the IO pin for other purposes.
can use AVR USB Programmer for programing this board.
Features
The board is built upon high quality FR-4(1.5 mm) with a green solder mask and a clear and legible white legend. All IO pins are labelled with their names along with any dual feature they support. This greatly simplifies prototyping.
Onboard 16x2 LCD support with contrast control
Onboard USB to Serial converter for serial communication and programming over USB
Onboard MAX232 interface circuit for easy communication with a computer and other serial devices(GPS modules, GSM Modems, etc).
DC plug-in jack for power input.
Onboard bridge rectifier enables the board to accept both AC and DC input voltages.
Onboard 5V regulator(LM7805) with filtering capacitors and heatsink.
Power Status LED(Green) and a general purpose LED(Red) connected to PB0.
The AVCC pin is connected to 5V through a 100 uH inductor for accurate ADC conversions.
Power Status LED(Green) and 4 x general purpose user LED(Red) and Switches
16 MHz Quartz crystal oscillator circuit.
Port extensions for all ports with detailed pin labeling for easy identification of pins
Vin, 5V and Gnd bus provided.
The board has 4 holes of 3mm diameter for easy mounting.
The package includes a CD and product manual.
The inc