Have a question? Call us now at +91 9650660070

care@industrybuying.com

Jt Products Online

Showing 17 out of 17 products

Sort by

Ships within 24 hrs

JT 4 Channel RELAY CARD

By JT

₹707

The JT 4 Channel Relay Card is a board with four independent relays. The relays can be controlled using an Arduino, and the card is also compatible with the Raspberry Pi. It can also be used in conjunction with systems that have industrial power supplies and other systems that require DC power sources to be switched on and off remotely. The relays are rated for 120 VAC / 240 VAC at 400 mA/240 VAC, and are designed to have a current-limiting circuit built-in so they will not burn out if the load is too heavy. The relays can handle up to 50VDC of input voltage, making this board ideal for use with 24VDC systems. When using the card in conjunction with an Arduino board, the relays will respond when receiving signals between 3 – 5 Volts. The input voltage for the card can be 12V DC. The output voltage of this relay board is 5V DC, which is safe and convenient for controlling low-voltage devices such as LED lights or solenoid valves. Each channel has an input terminal and an output terminal which allows you to connect these terminals with wires to control the device you want to turn on or off. The relay contacts can withstand about 10A current. The relay cards have many applications such as: home automation, industrial automation, vending machine control, robot control and etc. This card is a perfect solution for controlling high-power loads as well as providing isolated control of sensitive electronic equipment. This card can control up to four channels via a single relay output. It is designed with the same footprint as a PCI card so that it can be used in place of one in any computer case.

Ships within 4 days

JT 8 Channel RELAY CARD

By JT

₹1,143

The JT 8 Channel RELAY CARD is a reliable relay card with 8 channels, each of which can support up to 10A/250VAC or 2A/30VDC. It is ideal for industrial automation to control various kinds of electrical devices. It can work in the same time in Parallel, it can save cost and more easy to control. It is suggested for using for home automation control, security system control, traffic light monitoring control and so on. The card requires a bus-powered PCI slot and consumes approximately 2 watts of power (1 watt with the backlight off). Each relay has an independent contact rating of 30VDC at 1A or 250VAC at 2A, and can be triggered by an external signal or by internal timing. The external trigger input uses a 3-pin screw terminal, while the internal trigger input uses a 4-pin screw terminal. The timing input is provided via 16-pin header and allows for event control through software. When triggered, the relays turn on and remain active for 20 seconds before turning off automatically. This prevents unwanted relay chatter due to momentary surges in current draw, thereby ensuring that the card performs reliably over time. With the relay card, one can achieve a wide range of tasks including lighting control, heavy machinery automation, and anything else that requires switching on and off power supply. The device has 8 channels for remote control; each channel can be independently controlled. Each channel contains a relay output. The relay outputs are designed to control various loads with up to 10A 250VAC.

Ships within 4 days

JT Aluminium COUPLING

By JT

₹707

The JT Aluminium COUPLING is a machined aluminium coupling that is used for connecting two shafts. The coupling has an internal lining made from polyurethane, which helps to reduce the amount of friction between the two shafts. The coupling is divided into three parts: a male part, a female part and an adaptor. The adaptor can be used to connect the male and female parts together and allows for easy positioning. The male and female parts have grooves that allow the coupler to be able to be positioned easily. They are known for their durability, easy installation and low maintenance cost due to which they are used in various applications such as mills, refineries, steel plants, power plants, chemical plants, fertilizer plants, offshore platforms etc. The coupling is made from high quality aluminium alloy that makes it both durable and lightweight. Coupling for door, window and also roof with large range of sizes available to meet individual needs. The coupling is designed to connect two lengths of tubing or pipe, enabling them to be joined securely and effectively. It can be used for air conditioning and refrigeration systems, hot and cold water distribution systems, gas fired domestic hot water systems, solar hot water systems, vacuum pumps and other transportation industries. The coupling has good corrosion resistance and high efficiency. It is designed for high pressure (above 3.0Mpa).It is made of extruded aluminium alloy 6061-T6 or 7075-T6 with a hard anodized coating to protect against corrosion. The length of the pipe coupling is available in 1m, 2m, and 3m all with a diameter of 50mm.

JT 2m Cable Length 10mm Shaft ENCODER-PPR 1024

Ships within 3 days

JT 2m Cable Length 10mm Shaft ENCODER-PPR 1024

By JT

₹6,961

JT 2m Cable Length 10mm Shaft ENCODER is an encoder used with a motor. It is one part of the motor's control circuit. The other is the power supply and motor controller. The encoder can be used in applications where the shaft of the device must be mechanically rotated and its angular position or direction needs to be monitored by a sensor. It can also be used to sense the presence of an object in close proximity to the shaft. The output signal is a pulse train and the clock frequency can reach 8KHz. It can be widely used in discrete and intelligent home appliances, such as washing machine, dishwasher, refrigerator, oven, microwave oven, air conditioner and vacuum cleaner. The measurement range is 0--359 degree with a resolution of 1 degree and an accuracy of ±10 degree. The output signal is 4-20mA or 0-10V. It measures the rotational movement of the axis and transmits it to the Bluetooth module by using a rotary encoder. The length of the cable shall be 2m. The cable shall have 10mm diameter shaft. The connectors are male and female type. It's sturdy, with a rugged outer shell. The buttons are easy to press and are labeled clearly to indicate the direction of rotation and the movement of the shaft. It has a backup battery, so it can continue to function even when there's no power source available. It's easy to connect this product to other JT devices using the standard 10mm port. This is ideal for working with different kinds of equipment and devices.

Related Searches

jt touch screen

jt encoder accessories

JT 8 Channel 5A Switching Current RELAY CARD

Ships within 4 days

JT 8 Channel 5A Switching Current RELAY CARD

By JT

₹1,887

The JT 8 Channel 5A Switching Current RELAY CARD is a high-density relay card designed for industrial control applications, such as machine power control, automation, networking and so on. The relay card supports 8 channels of 5A current output and each channel can be turned on or off by external signals (typically from industrial controls). The relay card integrates relays and driver chips with advanced switching technology and the use of high-quality electronic components to achieve outstanding performance. It can protect the circuit from transient over-voltage and overcurrent, as well as from abnormal voltage drop. The relay card also has excellent surge protection and anti-interference ability to ensure stable operation. It is designed to drive the relays directly and can be used in many industrial applications such as the control circuit of a machine tool, or automatic door opener or remote control and so on. In the event of a failure or when switching between high motor power and low motor power, it will quickly switch the high-power circuit to low-power circuit by pressing one key on the remote control board. With built-in overheat protection, it will automatically detect whether there is a short circuit or overload and shut down when overheating occurs, so it has good protection against short circuits and overload. This product has high reliability, small volume, and easy installation in harsh environment. It is suitable for control of air conditioners, electric fans, home appliances, lighting equipment and other large current loads. It has a built-in timer function that can be used to control the ON/OFF time.

JT 5m Cable Length 10mm Shaft ENCODER-PPR 1024

Ships within 4 days

JT 5m Cable Length 10mm Shaft ENCODER-PPR 1024

By JT

₹7,551

The JT 5m Cable Length 10mm Shaft ENCODER-PPR 1024 is a high performance, compact machine encoder. It offers flexible, plug and play connection to an unlimited range of motion systems and is also available in lengths of 2, 5 or 8 meters. It supports a single-ended connection, which eliminates the need for a separate power supply. This increases flexibility and prevents any potential interference with the servo power line. The encoder provides absolute position information, allowing the drive system to maintain closed loop control of position during acceleration and deceleration. The high-performance magnetic core has been designed for smooth and trouble-free operation. It has high compatibility with different systems, such as Windows98/SE/ME/2000/XP, Linux, and so on. The cable is made of high-quality PVC material which is resistant to heat and acid. The encoder is user-friendly with plug-and-play function. Operating voltage: DC7~14V. t comes with a standard 5m cable and a 10mm shaft. This encoder has 1024 counts per revolution of the output shaft. This cable can be used as an external encoder signal cable on a JT 10k or 20k servo. The cable also has a connector at the end that will allow you to connect it to the main board of the servo. The cable length can be adjusted before the order is placed to ensure that the connector and sensor are in the appropriate locations. The shaft diameter and configuration are also customizable, as well as the mounting hardware, although the standard mounting hardware is included with each order.

Ships within 4 days

JT 4.3Inch Without Ethernet Touch Panel

By JT

₹11,209

The JT 4.3Inch Without Ethernet Touch Panel is a touchscreen monitor that allows users to navigate through the functions of their computer with ease. This monitor comes equipped with a HDMI port and VGA port to accommodate both PC and Mac computers. It requires an operating system of Windows XP/7 or OS X 10.4. However, it does not require an internet connection for use, and can connect to the internet through Ethernet or wireless functionality if desired. The screen size measures in at 4 inches diagonally, which is ideal for those who want a monitor that is not too large and not too small. The frame of this touchscreen monitor is made of plastic, but has a sleek black finish that helps it blend into almost any environment without attracting unwanted attention or becoming an eyesore. It works by taking the information that is on the computer and projecting it onto a glass screen so that it can be viewed by everyone in the room. It is able to do this because of a system called Digital Micromirror Device (DMD), which has an LED inside of it that can be manipulated by the computer. This model can be used in applications such as network products, home appliances, security products, industrial communication equipment, signage, mobile phone accessories and other applications requiring touch-screen technology. The screen is designed for use in POS (Point of Sale) systems, interactive kiosks, digital signage and other devices that require a high-quality 4.3" touch screen monitor. It also features an SD card reader that allows users to store data on the touchscreen monitor's internal memory and play videos directly from the SD card inserted into the reader slot.

Ships within 4 days

JT 7Inch Without Ethernet Touch Panel

By JT

₹15,339

The JT 7" Touch Panel is a 7-inch touch screen with no Ethernet interface. This product is ideal for those who want to enjoy the convenience of a portable display without the need for networking. The touch panel is compatible with a variety of applications, such as car navigation, information and advertisement display, point-of-sale systems and kiosks. It also has an onboard power supply and mounting points so you can simply bolt it down to your device and plug it in. It has many attractive features such as high definition video resolution, wide view angle, large display area and good price. Its touch feature can help you to use your fingers instead of mouse to operate your PC. And it allows you to have more convenience and efficiency while working. Its high definition 7inch multi-point capacitive touch screen delivers stunning images and videos in full HD 1080P resolution that bring you into the world of entertainment. This tablet pc is equipped with a wide range of connectivity options. This touch screen can be widely used in KTV / bar, home appliance, electronic products, games machine, etc. It is a 70/30 split between laminate and thermoplastic. The thermoplastic is made of a three-layer structure with a smooth surface finish, while the laminated portion features an opaque black backing to conceal components and provide stability. To provide proper resistance against wear and tear, the front layer of the thermoplastic is 0.04" thick, while the back layer is 0.08". The sheet can be cut to size, but must be done so with care as it could be easily scratched if improperly handled.

Ships within 4 days

JT 7Inch With Ethernet Touch Panel

By JT

₹18,879

The JT 7Inch with Ethernet Touch Panel is a touch screen terminal for controlling the data collection device, which supports TFT LCD display and touch screen operation. The display size of the terminal is 7 inches, and it has a power adapter. The terminal can be used to control the data collection device by entering or selecting data directly or by entering commands in the command input window. The commands can be entered through the keyboard on the screen or by using the serial port. The enter and cancel buttons are used to select and deselect items on the screen, and they can also be used to confirm or cancel selections. The terminal uses TCP/IP networks to communicate with the data collection device. In addition, it has a web server that provides status displays, allows configuration settings to be stored on a USB flash drive, and more. The wireless capabilities of the JT 7Inch With Ethernet Touch Panel give customers the ability to use it for a wide range of applications, including public safety and security, retail, hospitality, transportation, and much more. The control panel is located on the bottom right-hand corner of the screen. It has buttons for power, menu, up, down, left, right, and enter. The menus are simple enough to navigate through and easy to understand. There is also a link button which will take you to a backlight menu where you can choose your own custom color scheme and brightness. The backlight is bright enough to be seen in most circumstances and the color quality is excellent. The display itself is clear and sharp, without any noticeable lag time or any flickering issues.

JT 5m Cable Length 10mm Shaft ENCODER-PPR 3600

Ships within 4 days

JT 5m Cable Length 10mm Shaft ENCODER-PPR 3600

By JT

₹15,339

The JT 5m Cable Length 10mm Shaft ENCODER-PPR 3600 is a device that can be installed in the wheels of motorized vehicles. It is made to transmit information on the rotational speed and direction of a vehicle, along with its position, to a receiver. This allows the receiver to determine whether a vehicle is moving and how fast it is going at any given time. A wireless sensor like the JT 5m Cable Length 10mm Shaft ENCODER-PPR 3600 is more reliable than a wired connection, as it avoids the problems that can occur with cables, including entanglement and breakage. The power supply for this device must be between 3 and 28 volts DC, and an input voltage of less than 28 volts will result in an output voltage of 0V. The device can operate between -40oC (-40oF) and +85oC (185oF). The sensor module is housed in a compact IP65 metal/plastic enclosure that can be used in either horizontal or vertical installations. This sensor module is typically used to sense the position of a valve or other operator. The position of the shaft can be sensed at any point along its length by using multiple modules together. The output voltage will be zero when the shaft is at 90° and will increase linearly from zero to 5V as the shaft rotates through 0° to 360°. This encoder outputs voltage, which makes it great for use with a motor. Connections are made via the 8-pin connector, which is included with the product. The JT 5m Cable Length 10mm Shaft ENCODER-PPR 3600 is powered by 24 Volts DC and outputs a maximum voltage of 28 volts DC.

JT 1m Cable Length 10mm Shaft ENCODER -PPR 5000

Ships within 4 days

JT 1m Cable Length 10mm Shaft ENCODER -PPR 5000

By JT

₹14,159

The JT 1m Cable Length 10mm Shaft ENCODER -PPR 5000 is a product that measures and transmits the speed of rotating shafts. It is available in several different lengths, with cable diameters from 0.5 to 10 mm. The cable length can be customized by using any of the encoders with different fixed or separable cables. The encoder is equipped with Hall Effect sensors with high position accuracy and long life, which ensures that the servo drive is always in the correct position. The operation of the encoder is reliable, simple, and easy to use. The cable length is 1000 mm, and it has a 10-mm shaft diameter. The unit has two cables - one 4-wire cable and one 6-wire cable. It is compatible with most serial interface controllers and is supplied with mounting hardware. This product has a cable length of one meter, has a 10mm shaft diameter, and is made for use with a 5V power supply. It comes with integrated ENCODER technology for increased reliability and protection against environmental influences such as shock and vibration. The JT 1m cable length 10mm shaft encoder also comes with an IP67 rating, which means it is water resistant as well as protected against dust infiltration. This encoder is designed to be used in conjunction with their other motion control products and components. The output pulse is available in either a proportional or absolute mode, or both simultaneously. A built-in watchdog timer is included to detect position loss with output pulses. The short-circuit protection prevents the encoder from damage if connected to a faulted system and the over voltage protection ensures reliable operation at any power supply voltage in the range of 12–30VDC.

JT 5m Cable Length 10mm Shaft ENCODER-PPR 360

Ships within 4 days

JT 5m Cable Length 10mm Shaft ENCODER-PPR 360

By JT

₹7,787

The JT 5m Cable Length 10mm Shaft ENCODER-PPR 360 can be used to wrap around objects or attach to equipment, making it a versatile tool in many areas. It has a diameter of 0.8 inches, and it can protect the encoder from damage from impact or vibration. This type of encoder is small and easy to use, and it works with most common types of sensors. The shaft is composed of steel, which makes it strong and secure, so it can withstand heavy pressure without bending. It also has a connector made of PBT that is durable, so it will not crack even when the encoder is dropped or placed under pressure. When a sensor is attached to the motor output, it can then determine how far or fast the motor has moved by processing how quickly the angle has changed. This is done with either an incremental or absolute encoder. An incremental encoder will give you change in position only for every full revolution of the shaft; however, an absolute encoder will provide more resolution and can be programmed to count any change in angle at any time. It works by sending a signal to a receiver, which then processes the information and takes the necessary action. This receiver can be programmed to receive signals from anywhere within a radius of up to 100 meters, and these signals can be changed between different remote controls. It is also good for use in any situation that requires motion detection, such as opening automatic doors or turning off lights when no one is in the room.It is also used in the small robot, automatic control system, home appliance and other application with small size and high precision.

JT 2m Cable Length 10mmShaft ENCODER-PPR 2500

Ships within 4 days

JT 2m Cable Length 10mmShaft ENCODER-PPR 2500

By JT

₹9,321

JT 2m Cable Length 10mmShaft ENCODER-PPR 2500This sensor is used for long distance detection. It can be widely applied for the field of industrial control, scientific research, machine vision systems, automatic product identification and monitoring, automotive industry, etc. This Encoder is a good choice for manufacturing automation, robotics and other industrial applications. It is a high precision encoder with a very low noise and an excellent resolution. Its internal programmable processor and power supply makes it ideal for use in a wide variety of applications. The enclosure of the encoder is a cast aluminum housing with a gray epoxy finish. The dimensions of the enclosure are 36.5 x 36.5 x 27 mm. The length of the cable is 2 m with a 10 mm diameter shaft and mating connector at each end of the cable assembly. The encoder provides the ability to monitor linear and rotary position in closed loop control applications. It also comes with a minimum of 2500 counts per revolution, which means that it can provide accurate information to the connected system. The product is constructed from a steel and plastic material to ensure that it is durable and long lasting, making this product a great option for anyone who wants to use the product for many years or for multiple uses. Connected to a keypad, this encoder allows the user to rotate it 360 degrees and click eight buttons in a manner similar to that of a computer mouse. The unit's cable length is two meters long, and its shaft measures 10mm in diameter.

JT 1m Cable Length 10mm Shaft ENCODER-PPR2500

Ships within 4 days

JT 1m Cable Length 10mm Shaft ENCODER-PPR2500

By JT

₹9,085

The JT 1m Cable Length 10mm Shaft ENCODER-PPR2500 is a high-quality encoder that has a cable length of 1 m, a shaft diameter of 10 mm, and a resolution of 2048. The encoder measures the angular position with magnetic sensing and converts it into an electrical signal. This signal is then sent to the computer via the included USB cable. It features a built-in absolute rotary angle sensor with precision angle measurement and no magnetic interference from the motor. It is ideal for applications in the robotics industry, such as mobile platforms, industrial robots, and material handling robots. The encoder is a rotating wheel, disk, or drum composed of a number of equally spaced teeth, slots, or grooves. As the wheel or disk rotates, the signal from the encoder can be used to determine how far and in which direction it has been rotated. It's used in robot movement and positioning applications, including computer mice and video game consoles. Some drivers allow the user to set the resolution (or "step size") of the signal, allowing higher precision of measurement. Typical resolutions are 80 pulses per revolution (ppr), 100 ppr, 200 ppr, 400 ppr, and 1,000 ppr. The default resolution for many consumer-grade devices is 100 ppr. This model is specifically designed for use with DC brushed motors and comes with both clockwise and counter-clockwise rotation settings. The diameter of the shaft can be adjusted by loosening the set screws on the side of it and turning it to the desired diameter.

Ships within 3 days

JT 3Phase-415Voltage Panel Meter

By JT

₹2,005

JT 3Phase-415Voltage Panel Meter is a general purpose panel meter for the measurement of electrical power and energy in industrial, commercial and residential applications. The JT 3 Phase-415Voltage Panel Meter can be used for domestic purposes, such as for the measurement of household current, and also for commercial and industrial applications. This panel meter has a power range from 0.05A to 99.99A at a voltage range of 0V to 415V. Dual scale is provided on the meter face, indicating both RMS values (root mean square) and peak values of the measured circuit current or voltage. The dual scale facilitates the meter's use in all types of electrical meters such as current, voltage or power measurements. The upper rotary switch is used to select the measurement ranges, while the lower rotary switch is used to select the main phase voltage. The reading can be taken on the digital display through turning the selector knob on the left side of the panel meter. The instrument is designed to measure the voltage of three-phase electric power in a convenient and easy-to-read format. The unit has a simple dial face and requires no batteries or external power source. This makes it an economical solution for reliable and accurate measurements of three-phase voltages. They are suitable for use in both indoor and outdoor applications. These portable, easy to install panel meters are available with a choice of different connections and can be supplied with either single or dual ranges. It has large LCD display, so it can show the measured parameters of three phases clearly at the same time. It has wide measuring range 0-415V, which means that it can measure DC voltage and AC voltage in 415V power system.

Ships within 4 days

JT Digital 220V PROCESS INDICATOR

By JT

₹1,533

The JT Digital 220V PROCESS INDICATOR is a digital indicator that utilizes the latest in digital technology to ensure accuracy and precision in use. This device is equipped with a high-speed microcontroller, which automatically converts analog input into a digital signal and displays the results on an LCD screen. The device is capable of measuring multiple functions, including temperature and pressure. All that is required for the device to function properly is the electrical power source and connecting it to the appropriate sensor(s). It has two ranges: 0–200 mA and 0–4A. The large LCD display makes the data easy to read, even in dim lighting. The unit weighs in at only 1 lb and measures 6.5" x 2.75" x 1". The bright blue housing can be seen clearly across large distances. The indicator can also show negative values depending on the setting of the selector switch. It has two analog voltmeters capable of displaying voltage from 0 to 250 Volts DC and 0 to 500 Volts DC. It can be used for most application fields in industrial automation and factory automation. It comes with a serial number and an individual password that allows to access all functions on a user-specific basis. Thus the device can be used in multi-user systems that all have their own individual settings for the controller. The light source is housed behind a translucent lens that filters out visible light, allowing only ultraviolet radiation to pass through. A sensor on the front of the unit registers any level of ultraviolet exposure and translates it into a percentage value displayed on the front panel.

Ships within 5 days

JT ENC-1024 2m Encoder Hollow Shaft

By JT

₹8,259

The JT ENC-1024 2m Hollow Shaft Encoder is a drive shaft that can be used with any servo or motor. It is composed of aluminum, which means it is lightweight and sturdy at the same time. This shaft is hollow, so it may be used in a variety of applications where a hollow shaft is needed. The high quality solid shaft is precision machined for high rigidity, durability and reliability. It has a hardened steel ball support for stability and smooth rotation. The gear head is made of stainless steel for long lasting performance. This product features a 4mm diameter through hole, and has an output frequency of 12,000 pulses per revolution. The popular plastic housing is UV stabilized with a clear polycarbonate cover to protect the internal components. The encoders are designed for use in harsh environments and are designed to withstand shock and vibration, making them ideal for use in automotive, industrial, and commercial applications. The angular resolution of the encoder is about 0.96°, and it has an error rate less than 0.002°/s. It has a maximum operating temperature of 70°C (under no load) to 80°C (under full load). The length of the shaft is 2 meters, and the diameter is 0.3 inches.

Page 1 of 1 results

Top Selling Jt Products Online Products Price List for December 2025

Product Name	Specifications	Expected Price	Dispatch Time	Discount
JT 4 Channel RELAY CARD	Channel 4 \| Height 1.8 cm	₹707	24 hrs	--
JT 2m Cable Length 10mm Shaft ENCODER-PPR 1024	Cable Length 2m \| Height 3 cm	₹6,961	3 days	--

This data was last updated on 09/12/2025

Helpline Number Call: +91 9650660070 (Mon-Sun: 9am-8pm)

Return within 7 days of receiving your order

100% Safe & Secure Payments Pay using secure payment methods

100% ORIGINAL guarantee for all products

Complete products 20,00,000+ products from 12,000+ Brands

Buyer Protection Committed to buyer interests to provide a smooth shopping experience.

Experience Industrybuying App

Follow us on

Company

Sister Site

Help