Have a question? Call us now at +91 9650660070

care@industrybuying.com

Hand Taps

Showing 40 out of 4632 products

Sort by

Inder 12.7 mm(1/2") - 14" BSP Carbon Steel Cut Thread Right Hand Taps 1005D

Ships within 24 hrs

INDER BSP 55 Deg Carbon Steel Cut Thread Right Hand Taps P-1005 Series

By INDER

Set of 2 piece

₹211 - ₹6,489

You save ₹226!

28.99% OFF

Series : P-1005

Thread : BSP

Material : Carbon Steel

Thread Angle : 55°

Type of Product : Cut Thread Hand Tap

Cutting Type : Right Hand

Addison BS CON (Zone 3) HSS Ground Thread Hand Tap (Size 5/8 Inch)

Ships within 24 hrs

Addison HSS BS Conduit (Zone 3) Ground Thread Hand Tap

By Addison

Pack of 3 piece

₹5,663 - ₹46,019

You save ₹3,316!

31.9% OFF

Features :
Addison - Hand Taps
- High Speed Steel

Thread : BS CON (Zone 3)

Material : High Speed Steel

Type of Product : HSS Ground Thread Hand Tap

Standard : BS 949-1951

Addison BSCY HSS Ground Thread Hand Tap (Size 5/16 Inch, TPI 26)

Ships within 24 hrs

Addison HSS BSCY Ground Thread Hand Tap

By Addison

Pack of 1 piece

₹494 - ₹7,197

You save ₹170!

23.14% OFF

Features :
Addison - Hand Taps
- High Speed Steel

Thread : BSCY

Material : HSS

Type of Product : Ground Thread Hand Tap

Standard : BS 949-1951

TOTEM UNF Straight Flute HSS Hand Tap 9.50 mm (3/8 inch)

Ships within 2 days

TOTEM UNF Straight Flute HSS Hand Tap 9.50 mm (3/8 inch)

By TOTEM

Pack of 1 piece

₹943

These are straight flute general purpose taps which can be used for both machine or hand tapping. They are generally the most economical tool for use on production runs, but are best on materials that produce chips, or where the swarf breaks readily. Where deep holes are to be tapped, in materials which produce stringy swarf, other types of taps may be needed, especially for coarse threads.
Hand taps can be supplied in sets of three bottom, second and taper leads, or individually.
Taper Taps have a lead of 7-10 threads at 5 degrees per side. The taper lead distributes the cutting force over a large area, and the taper shape helps the thread to start. They can therefore be used to start a thread prior to use of second or bottom leads, or for through holes.
Second Taps have a lead of 3-5 threads at 8 degrees per side. They are the most popular and can be used for through holes, or blind holes where the thread does not need to go right to the bottom.
Bottom Taps have a chamfer (lead) of 1-2 threads, the angle of the lead being around 18 degrees per side. They are used to produce threads close to the bottom of blind holes.

MIRANDA TOOLS HSS Hand Tap Straight Flute SO3 Type Ground Thread Coarse Pitch, Size M1.6 x 0.35 mm (Set of 3)

Ships within 3 days

MIRANDA TOOLS HSS Hand Tap Straight Flute SO3 Type Ground Thread Coarse Pitch (Set of 3)

By MIRANDA TOOLS

Set of 3 piece

₹1,297 - ₹2,949

The MIRANDA TOOLS HSS Hand Tap Straight Flute SO3 Type Ground Thread Coarse Pitch, Size M1.6 x 0.35 mm (Set of 3) is a precision-engineered tool designed to deliver accuracy and reliability in demanding applications. Manufactured with high-speed steel (HSS), this tool ensures durability, long service life, and consistent performance even under rigorous use. Its carefully crafted straight flute design enables smooth cutting action, making it suitable for threading and tapping operations in a variety of materials. The MIRANDA TOOLS HSS Hand Tap Straight Flute SO3 Type Ground Thread Coarse Pitch, Size M1.6 x 0.35 mm (Set of 3) is built for professionals who require dependable performance in workshops, industrial settings, and maintenance tasks.With its robust construction and precise geometry, the MIRANDA TOOLS HSS Hand Tap Straight Flute SO3 Type Ground Thread Coarse Pitch, Size M1.6 x 0.35 mm (Set of 3) provides excellent chip evacuation, reduced cutting resistance, and improved surface finish. This makes it a versatile choice for machinists, engineers, and technicians seeking accuracy and efficiency. Whether used for general-purpose threading or specialized tasks, the MIRANDA TOOLS HSS Hand Tap Straight Flute SO3 Type Ground Thread Coarse Pitch, Size M1.6 x 0.35 mm (Set of 3) guarantees reliability and ease of use. Its high-quality material and superior workmanship ensure long-lasting performance, making it an essential addition to any professional toolkit.

Thread : Ground Thread

Material : High Speed Steel

Type of Product : HSS Hand Tap

Flute Type : Straight Flute

Pitch Type : Coarse Pitch

Finish Type : Bright Finish

Usage For : Internal Thread formation in Components

Country of Origin : India

Tap Type : SO3

Standard Compliance : IS 6175 - Part 1, 2 & 3 - 1992

TOTEM Straight Flute BA Thread Hand Tap (BA Size No. 5)

Ships within 2 days

TOTEM Straight Flute BA Thread Hand Tap (BA Size No. 5)

By TOTEM

Pack of 1 piece

₹683

Features -
TOTEM - Hand Taps [HSS]
- High Speed Steel

Inder 20 mm Carbon Steel Cut Thread Left Hand Tap 1004O

Ships within 4 days

INDER Carbon Steel Cut Thread Left Hand Tap P-1004 Series (Size 20-50 mm)

By INDER

Set of 3 piece

₹1,297 - ₹15,339

You save ₹53!

3.92% OFF

Series : P-1004

Material : Carbon Steel

Thread Angle : 60°

Type of Product : Cut Thread Hand Tap

Cutting Type : Left Hand

TOTEM 6.35 mm (1/4 inch) HSSE TIN Silver Cut Tap FAB0205308

Ships within 3 days

TOTEM 6.35 mm (1/4 inch) HSSE TIN Silver Cut Tap FAB0205308

By TOTEM

₹943 ~~₹1,204~~

You save ₹261!

21.65% OFF

Edge treatment for reduced axial force and torque, makes the tool run more smoothly, reduces risk of cutting-edge chipping and improves surface quality, tool life and chip evacuation The design of the spiral flute secures a constant rake angle and gives a constant cutting process Back chamfer, used on taps with high helix angle, reduces torque and chipping

Addison BSP HSS Parallel Ground Thread Hand Tap 1/8 inch (Pack of 2)

Ships within 3 days

Addison BSP Parallel HSS Ground Thread Hand Tap (Pack of 2)

By Addison

₹1,533 - ₹3,06,799

Addison BSP HSS Parallel Ground Thread Hand Tap 1/8 inch A parallel ground thread hand tap is a specific type designed for threading operations. Similar to other hand taps, it is manually operated and used for creating threads in pre-drilled holes. The "parallel ground thread" designation indicates a specific thread geometry that distinguishes it from other taps The term "parallel ground thread" refers to the uniformity of the threads along the tap's length. Unlike taper taps with a gradual starting point, parallel ground thread taps maintain a consistent diameter from the tip to the end. This design is advantageous for creating threads with a constant depth Parallel ground thread hand taps are commonly used in through-hole applications where the hole extends entirely through the workpiece. They are suitable for materials such as metal, plastic, or wood. The parallel thread design ensures that the tap can cut threads along the entire length of the hole without tapering towards the bottom Similar to other hand taps, parallel ground thread hand taps are available in three main types: taper, plug, and bottoming. The taper version has a more gradual starting point, the plug version is a middle-ground option, and the bottoming version has a shorter chamfer for threading closer to the bottom of holes These hand taps are typically constructed from high-speed steel (HSS) or other durable materials. Some may feature coatings like TiN or TiAlN to enhance their wear resistance and tool life, especially when working with more rigid materials or in demanding cutting conditions The parallel ground thread hand tap is operated manually like all hand taps. The user turns the tap by hand to cut threads into the workpiece. This manual operation provides the operator with control over the threading process The parallel ground thread design ensures precision in thread depth and diameter, making these taps suitable for applications where consistent thread dimensions are critical. Their versatility makes them valuable in various industries, including manufacturing, maintenance, and repair

Thread : BSP

Material : HSS

Type of Product : Parallel Ground Thread Hand Tap

Standard : BS: 949 - 1951

Inder 24 mm Carbon Steel Cut Thread Right Hand Tap 1004Q

Ships within 4 days

INDER Carbon Steel Cut Thread Right Hand Tap P-1004 Series (Size 20-50 mm)

By INDER

Set of 3 piece

₹1,108 - ₹12,979

You save ₹153!

7.97% OFF

Series : P-1004

Material : Carbon Steel

Thread Angle : 60°

Type of Product : Cut Thread Hand Tap

Cutting Type : Right Hand

TOTEM UNF Straight Flute HSS Hand Tap 5/16 Inch

Ships within 2 days

TOTEM UNF Straight Flute HSS Hand Tap 5/16 Inch

By TOTEM

Pack of 1 piece

₹789

Inder 3 mm Carbon Steel Cut Thread Right Hand Tap 1004B

Ships within 4 days

INDER Carbon Steel Cut Thread Right Hand Tap P-1004 Series (Size 2-18 mm)

By INDER

Set of 3 piece

₹103 - ₹719

You save ₹6!

4.1% OFF

Series : P-1004

Material : Carbon Steel

Thread Angle : 60°

Type of Product : Cut Thread Hand Tap

Cutting Type : Right Hand

MIRANDA TOOLS HSS Metric Fine Tap Straight Flute SO3 Type, Size M8.0 x 0.75 mm (Set of 3)

Ships within 3 days

MIRANDA TOOLS HSS Metric Fine Tap Straight Flute SO3 Type, Size M4.0 to M15 (Set of 3)

By MIRANDA TOOLS

Set of 3 piece

₹1,887 - ₹5,191

The MIRANDA TOOLS HSS Metric Fine Tap Straight Flute SO3 Type, Size M8.0 x 0.75 mm (Set of 3) is a precision-engineered threading tool designed for accuracy, durability, and performance in demanding applications. Constructed from high-speed steel (HSS), it ensures excellent wear resistance and consistent cutting results. Its design allows for smooth thread formation, reducing cutting resistance while extending tool life. This makes the MIRANDA TOOLS HSS Metric Fine Tap Straight Flute SO3 Type, Size M8.0 x 0.75 mm (Set of 3) suitable for professional machinists, workshops, and industries requiring reliable threading solutions.With the MIRANDA TOOLS HSS Metric Fine Tap Straight Flute SO3 Type, Size M8.0 x 0.75 mm (Set of 3), users can achieve clean, accurate threads across a variety of materials such as mild steel, aluminum, and brass. Its geometry supports efficient chip removal and stable performance, making it ideal for both general-purpose and specialized threading tasks. Whether used in automotive, aerospace, or general engineering applications, the MIRANDA TOOLS HSS Metric Fine Tap Straight Flute SO3 Type, Size M8.0 x 0.75 mm (Set of 3) delivers high-quality results and dependable operation for critical threading jobs.

Material : High Speed Steel

Type of Product : Metric Fine Tap

Flute Type : Straight Flute

Pitch Type : Fine

Set Quantity : 3 Pcs

Usage For : Creating Threads

Country of Origin : India

Thread Standard : Metric

Tap Type : SO3

Inder 3/8" - 18 NPT Carbon Steel Cut Thread Right Hand Taps 1006C

Ships within 4 days

INDER NPT Carbon Steel Cut Thread Right Hand Taps P-1006 Series

By INDER

Set of 2 piece

₹365 - ₹9,557

You save ₹47!

7.06% OFF

Series : P-1006

Thread : NPT

Material : Carbon Steel

Thread Angle : 60°

Type of Product : Cut Thread Hand Tap

Cutting Type : Right Hand

TOTEM BSP Straight Flute HSS Hand Tap 12.7 mm (1/2 Inch) (Pack of 2)

Ships within 2 days

TOTEM BSP Straight Flute HSS Hand Tap 12.7 mm (1/2 Inch) (Pack of 2)

By TOTEM

Pack of 2 piece

₹6,371

MIRANDA TOOLS Spirex M8 x 1.25 mm Tialn Platinum Cut Tap MB3

Ships within 4 days

MIRANDA TOOLS MB3 Spirex Series HSS Spiral Flute Platinum Cut Tap

By MIRANDA TOOLS

₹813 - ₹2,359

You save ₹468!

32.62% OFF

Series : Spirex

Material : HSS

Type of Product : Platinum Cut Tap

TOTEM 14 x 1.25mm TiN Gold HSS Straight Fluted Tap

Ships within 2 days

TOTEM 14 x 1.25mm TiN Gold HSS Straight Fluted Tap

By TOTEM

₹1,769 ~~₹2,074~~

You save ₹305!

14.72% OFF

• Cutting edge geometry production short chips
• Special process for stress relieving on cutting edge
• Radial and axial through coolant taps

TOTEM FAB0208244 M2 X 0.45mm HSSE Uncoated Silver Cut Tap

Ships within 2 days

TOTEM FAB0208244 M2 X 0.45mm HSSE Uncoated Silver Cut Tap

By TOTEM

₹990 ~~₹1,257~~

You save ₹267!

21.22% OFF

MIRANDA TOOLS HSS Hand Tap Spiral Flute Tin Type Ground Thread Coarse Pitch, Size M6.0 x 1.00 mm

Ships within 3 days

MIRANDA TOOLS HSS Hand Tap Spiral Flute Tin Type Ground Thread Coarse Pitch

By MIRANDA TOOLS

₹660 - ₹7,433

The MIRANDA TOOLS HSS Hand Tap Spiral Flute Tin Type Ground Thread Coarse Pitch, Size M6.0 x 1.00 mm is a precision-engineered tool designed to deliver accuracy and reliability in demanding applications. Manufactured with high-speed steel (HSS), this tool ensures durability, long service life, and consistent performance even under rigorous use. Its carefully crafted straight flute design enables smooth cutting action, making it suitable for threading and tapping operations in a variety of materials. The MIRANDA TOOLS HSS Hand Tap Spiral Flute Tin Type Ground Thread Coarse Pitch, Size M6.0 x 1.00 mm is built for professionals who require dependable performance in workshops, industrial settings, and maintenance tasks.With its robust construction and precise geometry, the MIRANDA TOOLS HSS Hand Tap Spiral Flute Tin Type Ground Thread Coarse Pitch, Size M6.0 x 1.00 mm provides excellent chip evacuation, reduced cutting resistance, and improved surface finish. This makes it a versatile choice for machinists, engineers, and technicians seeking accuracy and efficiency. Whether used for general-purpose threading or specialized tasks, the MIRANDA TOOLS HSS Hand Tap Spiral Flute Tin Type Ground Thread Coarse Pitch, Size M6.0 x 1.00 mm guarantees reliability and ease of use. Its high-quality material and superior workmanship ensure long-lasting performance, making it an essential addition to any professional toolkit.

Thread : Ground Thread

Material : High Speed Steel

Type of Product : HSS Hand Tap

Flute Type : Spiral

Pitch Type : Coarse Pitch

Finish Type : Bright Finish

Usage For : Internal Thread formation in Components

Pack of : 1 Pc

Country of Origin : India

Tap Type : Spiral Flute Tin

Standard Compliance : IS 6175 - Part 1, 2 & 3 - 1992

Inder 18 mm Carbon Steel Cut Thread Left Hand Tap 1004N

Ships within 4 days

INDER Carbon Steel Cut Thread Left Hand Tap P-1004 Series (Size 2-18 mm)

By INDER

Set of 3 piece

₹152 - ₹955

You save ₹79!

7.61% OFF

Series : P-1004

Material : Carbon Steel

Thread Angle : 60°

Type of Product : Cut Thread Hand Tap

Cutting Type : Left Hand

TOTEM M8 X 1.25mm HSSE TIALN Silver Cut Tap FAB0203680

Ships within 2 days

TOTEM M8 X 1.25mm HSSE TIALN Silver Cut Tap FAB0203680

By TOTEM

₹766 ~~₹1,001~~

You save ₹235!

23.45% OFF

Totem 8x1.25 mm Ground Thread Metric Coarse Pitch Series Hand Tap - FAA0202003 (Pack of 3)

Ships within 5 days

Totem 8x1.25 mm Ground Thread Metric Coarse Pitch Series Hand Tap - FAA0202003 (Pack of 3)

By TOTEM

Pack of 3 piece

₹2,477

Totem presents 8x1.25 mm Ground Thread Metric Coarse Pitch Series Hand Tap - FAA0202003 (Pack of 3). Totem is a brand that has been making high quality, precision tools for more than 40 years. Made from high speed steel, these hand taps are used for forming threaded holes inside a piece of material. The taps feature a spiral point with a cutting angle of about 15 degrees which results in a thread that is both larger and sharper than one produced by a standard plug tap. The cutting edge is ground with a 5/16" radius which allows the taps to produce threads with better strength and durability when compared to similar tools.
Made of High Speed Steel, these hand taps are used for forming threaded holes inside a piece of material. The tap is screwed into the hole at a specific angle and is then turned, creating threads in the hole to which a screw can be attached. These hand taps are featured in a 2-piece set with a tap handle, or in a 3-piece set that includes an extra tap handle in case one breaks.
The taps are designed to be used with a hand tool called an arbor press. To use, begin by selecting the correct sized tap for the job. Then, place the tap into the arbor press on top of the threaded hole you want to create. In order to accurately create threads, the hole you're tapping into should be as perfectly round as possible—this can be accomplished using an end mill or reamer or by using a lathe if you have access to one. When using the arbor press, apply pressure slowly and evenly down onto the top of the tap while simultaneously turning it with your hand until it reaches its maximum depth in the hole.

Inder 2" - 11 BSPT Carbon Steel Cut Thread Right Hand Tap 1006K

Ships within 4 days

INDER BSPT Carbon Steel Cut Thread Right Hand Taps P-1006 Series

By INDER

Set of 2 piece

₹365 - ₹9,557

You save ₹2,752!

22.35% OFF

Series : P-1006

Thread : BSPT

Material : Carbon Steel

Thread Angle : 55°

Type of Product : Cut Thread Hand Tap

Cutting Type : Right Hand

TOTEM 3.5 x 0.6mm TiN Gold HSS Straight Fluted Tap

Ships within 2 days

TOTEM 3.5 x 0.6mm TiN Gold HSS Straight Fluted Tap

By TOTEM

₹435 ~~₹585~~

You save ₹150!

25.68% OFF

• Cutting edge geometry production short chips
• Special process for stress relieving on cutting edge
• Radial and axial through coolant taps

TOTEM 2.5 x 0.45mm TiN Gold HSS Straight Fluted Tap

Ships within 2 days

TOTEM 2.5 x 0.45mm TiN Gold HSS Straight Fluted Tap

By TOTEM

₹660 ~~₹864~~

You save ₹204!

23.59% OFF

• Cutting edge geometry production short chips
• Special process for stress relieving on cutting edge
• Radial and axial through coolant taps

TOTEM M16 X 1.5mm HSSE TIALN Long Silver Cut Tap FAB0203283

Ships within 2 days

TOTEM M16 X 1.5mm HSSE TIALN Long Silver Cut Tap FAB0203283

By TOTEM

₹2,831 ~~₹3,418~~

You save ₹587!

17.18% OFF

TOTEM M12 X 1.5mm HSSE TIALN Long Silver Cut Tap FAB0200864

Ships within 2 days

TOTEM M12 X 1.5mm HSSE TIALN Long Silver Cut Tap FAB0200864

By TOTEM

₹2,477 ~~₹2,910~~

You save ₹433!

14.88% OFF

Totem 6x1 mm Ground Thread Metric Coarse Pitch Series Hand Tap - FAA0201939 (Pack of 3)

Ships within 5 days

Totem 6x1 mm Ground Thread Metric Coarse Pitch Series Hand Tap - FAA0201939 (Pack of 3)

By TOTEM

Pack of 3 piece

₹2,123

Totem presents 6x1 mm Ground Thread Metric Coarse Pitch Series Hand Tap - FAA0201939 (Pack of 3). Totem is a brand that has been making high quality, precision tools for more than 40 years. Made from high speed steel, these hand taps are used for forming threaded holes inside a piece of material. The taps feature a spiral point with a cutting angle of about 15 degrees which results in a thread that is both larger and sharper than one produced by a standard plug tap. The cutting edge is ground with a 5/16" radius which allows the taps to produce threads with better strength and durability when compared to similar tools.
Made of High Speed Steel, these hand taps are used for forming threaded holes inside a piece of material. The tap is screwed into the hole at a specific angle and is then turned, creating threads in the hole to which a screw can be attached. These hand taps are featured in a 2-piece set with a tap handle, or in a 3-piece set that includes an extra tap handle in case one breaks.
The taps are designed to be used with a hand tool called an arbor press. To use, begin by selecting the correct sized tap for the job. Then, place the tap into the arbor press on top of the threaded hole you want to create. In order to accurately create threads, the hole you're tapping into should be as perfectly round as possible—this can be accomplished using an end mill or reamer or by using a lathe if you have access to one. When using the arbor press, apply pressure slowly and evenly down onto the top of the tap while simultaneously turning it with your hand until it reaches its maximum depth in the hole.

Totem 1/4” Dia Serial Form BSP Thread Hand Tap - FAA0204623 (Pack of 2)

Ships within 5 days

Totem 1/4” Dia Serial Form BSP Thread Hand Tap - FAA0204623 (Pack of 2)

By TOTEM

Pack of 2 piece

₹3,303

Totem presents 1/4” Dia Serial Form BSP Thread Hand Tap - FAA0204623 (Pack of 2). Totem is a brand that has been making high quality, precision tools for more than 40 years. Made from high speed steel, these hand taps are used for forming threaded holes inside a piece of material. The taps feature a spiral point with a cutting angle of about 15 degrees which results in a thread that is both larger and sharper than one produced by a standard plug tap. The cutting edge is ground with a 5/16" radius which allows the taps to produce threads with better strength and durability when compared to similar tools.
Made of High Speed Steel, these hand taps are used for forming threaded holes inside a piece of material. The tap is screwed into the hole at a specific angle and is then turned, creating threads in the hole to which a screw can be attached. These hand taps are featured in a 2-piece set with a tap handle, or in a 3-piece set that includes an extra tap handle in case one breaks.
The taps are designed to be used with a hand tool called an arbor press. To use, begin by selecting the correct sized tap for the job. Then, place the tap into the arbor press on top of the threaded hole you want to create. In order to accurately create threads, the hole you're tapping into should be as perfectly round as possible—this can be accomplished using an end mill or reamer or by using a lathe if you have access to one. When using the arbor press, apply pressure slowly and evenly down onto the top of the tap while simultaneously turning it with your hand until it reaches its maximum depth in the hole.

Totem 9/16” Dia Serial Form UNC Thread Hand Tap - FAA0201042 (Pack of 3)

Ships within 5 days

Totem 9/16” Dia Serial Form UNC Thread Hand Tap - FAA0201042 (Pack of 3)

By TOTEM

Pack of 3 piece

₹6,017

Totem presents 9/16” Dia Serial Form UNC Thread Hand Tap - FAA0201042 (Pack of 3). Totem is a brand that has been making high quality, precision tools for more than 40 years. Made from high speed steel, these hand taps are used for forming threaded holes inside a piece of material. The taps feature a spiral point with a cutting angle of about 15 degrees which results in a thread that is both larger and sharper than one produced by a standard plug tap. The cutting edge is ground with a 5/16" radius which allows the taps to produce threads with better strength and durability when compared to similar tools.
Made of High Speed Steel, these hand taps are used for forming threaded holes inside a piece of material. The tap is screwed into the hole at a specific angle and is then turned, creating threads in the hole to which a screw can be attached. These hand taps are featured in a 2-piece set with a tap handle, or in a 3-piece set that includes an extra tap handle in case one breaks.
The taps are designed to be used with a hand tool called an arbor press. To use, begin by selecting the correct sized tap for the job. Then, place the tap into the arbor press on top of the threaded hole you want to create. In order to accurately create threads, the hole you're tapping into should be as perfectly round as possible—this can be accomplished using an end mill or reamer or by using a lathe if you have access to one. When using the arbor press, apply pressure slowly and evenly down onto the top of the tap while simultaneously turning it with your hand until it reaches its maximum depth in the hole.

MIRANDA TOOLS HSS Hand Tap Second BT Type Ground Thread Coarse Pitch, Size M10 x 1.50 mm

Ships within 3 days

MIRANDA TOOLS HSS Hand Tap Second BT Type Ground Thread Coarse Pitch

By MIRANDA TOOLS

₹376 - ₹589

The MIRANDA TOOLS HSS Hand Tap Second BT Type Ground Thread Coarse Pitch, Size M10 x 1.50 mm is a precision-engineered tool designed to deliver accuracy and reliability in demanding applications. Manufactured with high-speed steel (HSS), this tool ensures durability, long service life, and consistent performance even under rigorous use. Its carefully crafted straight flute design enables smooth cutting action, making it suitable for threading and tapping operations in a variety of materials. The MIRANDA TOOLS HSS Hand Tap Second BT Type Ground Thread Coarse Pitch, Size M10 x 1.50 mm is built for professionals who require dependable performance in workshops, industrial settings, and maintenance tasks.With its robust construction and precise geometry, the MIRANDA TOOLS HSS Hand Tap Second BT Type Ground Thread Coarse Pitch, Size M10 x 1.50 mm provides excellent chip evacuation, reduced cutting resistance, and improved surface finish. This makes it a versatile choice for machinists, engineers, and technicians seeking accuracy and efficiency. Whether used for general-purpose threading or specialized tasks, the MIRANDA TOOLS HSS Hand Tap Second BT Type Ground Thread Coarse Pitch, Size M10 x 1.50 mm guarantees reliability and ease of use. Its high-quality material and superior workmanship ensure long-lasting performance, making it an essential addition to any professional toolkit.

Thread : Ground Thread

Material : High Speed Steel

Type of Product : HSS Hand Tap

Pitch Type : Coarse Pitch

Finish Type : Bright Finish

Usage For : Internal Thread formation in Components

Pack of : 1 Pc

Country of Origin : India

Tap Type : Second BT

Standard Compliance : IS 6175 - Part 1, 2 & 3 - 1992

MIRANDA TOOLS HSS Left Hand Tap Straight Flute Second Type, Size M6.0 x 1.00 mm

Ships within 3 days

MIRANDA TOOLS HSS Left Hand Tap Straight Flute Second Type

By MIRANDA TOOLS

₹565 - ₹6,607

The MIRANDA TOOLS HSS Left Hand Tap Straight Flute Second Type, Size M6.0 x 1.00 mm is a precision-engineered tool designed to deliver accuracy and reliability in demanding applications. Manufactured with high-speed steel (HSS), this tool ensures durability, long service life, and consistent performance even under rigorous use. Its carefully crafted straight flute design enables smooth cutting action, making it suitable for threading and tapping operations in a variety of materials. The MIRANDA TOOLS HSS Left Hand Tap Straight Flute Second Type, Size M6.0 x 1.00 mm is built for professionals who require dependable performance in workshops, industrial settings, and maintenance tasks.With its robust construction and precise geometry, the MIRANDA TOOLS HSS Left Hand Tap Straight Flute Second Type, Size M6.0 x 1.00 mm provides excellent chip evacuation, reduced cutting resistance, and improved surface finish. This makes it a versatile choice for machinists, engineers, and technicians seeking accuracy and efficiency. Whether used for general-purpose threading or specialized tasks, the MIRANDA TOOLS HSS Left Hand Tap Straight Flute Second Type, Size M6.0 x 1.00 mm guarantees reliability and ease of use. Its high-quality material and superior workmanship ensure long-lasting performance, making it an essential addition to any professional toolkit.

Material : High Speed Steel

Type of Product : Left Hand Tap

Flute Type : Straight Flute

Usage For : Internal Thread formation in Components

Country of Origin : India

Tap Type : Second

MIRANDA TOOLS BOT M4 x 0.7 mm Tialn Platinumcut Tap MC3

Ships within 4 days

MIRANDA TOOLS MC3 BOT Series HSS Straight Flute Platinum Cut Tap

By MIRANDA TOOLS

₹624 - ₹1,651

You save ₹242!

27.17% OFF

Series : BOT

Material : HSS

Type of Product : Platinum Cut Tap

Addison BSP Parallel HSS Ground Thread Hand Tap (Size 1.5 Inch)

Ships within 4 days

Addison BSP Parallel HSS Ground Thread Hand Tap

By Addison

₹577 - ₹86,139

You save ₹3,711!

27.48% OFF

Addison have a policy to build Precise tools which are of highest quality and to extend excellent technical service to the end-users. Addison, an ISO certified company, manufactures tools with high quality CNC machines, state-of-the art manufacturing technology, a well-equipped metallurgical lab, a Tool Tech Centre (R&D) and Total Quality Control which has put its metal cutting tools on par with the best brands of cutting tools in the world. The High Speed Steel and carbide rods used for manufacturing the above tools are of highest quality.

Thread : BSP

Material : HSS

Type of Product : Parallel Ground Thread Hand Tap

Standard : BS: 949 - 1951

TOTEM M8 X 1.25mm HSSE TIALN Silver Cut Tap FAB0200693

Ships within 2 days

TOTEM M8 X 1.25mm HSSE TIALN Silver Cut Tap FAB0200693

By TOTEM

₹742 ~~₹970~~

You save ₹228!

23.5% OFF

TOTEM M5 X 0.8mm HSSE TIALN Silver Cut Tap FAB0204443

Ships within 2 days

TOTEM M5 X 0.8mm HSSE TIALN Silver Cut Tap FAB0204443

By TOTEM

₹683 ~~₹897~~

You save ₹214!

23.84% OFF

TOTEM M20 X 2.5mm HSSE TIALN Silver Cut Tap FAB0200809

Ships within 2 days

TOTEM M20 X 2.5mm HSSE TIALN Silver Cut Tap FAB0200809

By TOTEM

₹3,539 ~~₹4,719~~

You save ₹1,180!

25% OFF

Totem 10x1.25 mm Metric Fine Pitch Series Hand Tap - FAA0202786 (Pack of 2)

Ships within 5 days

Totem 10x1.25 mm Metric Fine Pitch Series Hand Tap - FAA0202786 (Pack of 2)

By TOTEM

Pack of 2 piece

₹2,477

Totem presents 10x1.25 mm Metric Fine Pitch Series Hand Tap - FAA0202786 (Pack of 2). Totem is a brand that has been making high quality, precision tools for more than 40 years. Made from high speed steel, these hand taps are used for forming threaded holes inside a piece of material. The taps feature a spiral point with a cutting angle of about 15 degrees which results in a thread that is both larger and sharper than one produced by a standard plug tap. The cutting edge is ground with a 5/16" radius which allows the taps to produce threads with better strength and durability when compared to similar tools.
Made of High Speed Steel, these hand taps are used for forming threaded holes inside a piece of material. The tap is screwed into the hole at a specific angle and is then turned, creating threads in the hole to which a screw can be attached. These hand taps are featured in a 2-piece set with a tap handle, or in a 3-piece set that includes an extra tap handle in case one breaks.
The taps are designed to be used with a hand tool called an arbor press. To use, begin by selecting the correct sized tap for the job. Then, place the tap into the arbor press on top of the threaded hole you want to create. In order to accurately create threads, the hole you're tapping into should be as perfectly round as possible—this can be accomplished using an end mill or reamer or by using a lathe if you have access to one. When using the arbor press, apply pressure slowly and evenly down onto the top of the tap while simultaneously turning it with your hand until it reaches its maximum depth in the hole.

Totem 1/2” Dia Serial Form BSP Thread Hand Tap - FAA0204662 (Pack of 2)

Ships within 5 days

Totem 1/2” Dia Serial Form BSP Thread Hand Tap - FAA0204662 (Pack of 2)

By TOTEM

Pack of 2 piece

₹6,489

Totem presents 1/2” Dia Serial Form BSP Thread Hand Tap - FAA0204662 (Pack of 2). Totem is a brand that has been making high quality, precision tools for more than 40 years. Made from high speed steel, these hand taps are used for forming threaded holes inside a piece of material. The taps feature a spiral point with a cutting angle of about 15 degrees which results in a thread that is both larger and sharper than one produced by a standard plug tap. The cutting edge is ground with a 5/16" radius which allows the taps to produce threads with better strength and durability when compared to similar tools.
Made of High Speed Steel, these hand taps are used for forming threaded holes inside a piece of material. The tap is screwed into the hole at a specific angle and is then turned, creating threads in the hole to which a screw can be attached. These hand taps are featured in a 2-piece set with a tap handle, or in a 3-piece set that includes an extra tap handle in case one breaks.
The taps are designed to be used with a hand tool called an arbor press. To use, begin by selecting the correct sized tap for the job. Then, place the tap into the arbor press on top of the threaded hole you want to create. In order to accurately create threads, the hole you're tapping into should be as perfectly round as possible—this can be accomplished using an end mill or reamer or by using a lathe if you have access to one. When using the arbor press, apply pressure slowly and evenly down onto the top of the tap while simultaneously turning it with your hand until it reaches its maximum depth in the hole.

MIRANDA TOOLS HSS Hand Tap Straight Flute Serial SO3 Type Ground Thread Coarse Pitch, Size M8.0 x 1.25 mm (Set of 3)

Ships within 3 days

MIRANDA TOOLS HSS Hand Tap Straight Flute Serial SO3 Type Ground Thread Coarse Pitch, Size M3 to M48 (Set of 3)

By MIRANDA TOOLS

Set of 3 piece

₹1,415 - ₹61,359

The MIRANDA TOOLS HSS Hand Tap Straight Flute Serial SO3 Type Ground Thread Coarse Pitch, Size M8.0 x 1.25 mm (Set of 3) is a precision-engineered tool designed to deliver accuracy and reliability in demanding applications. Manufactured with high-speed steel (HSS), this tool ensures durability, long service life, and consistent performance even under rigorous use. Its carefully crafted straight flute design enables smooth cutting action, making it suitable for threading and tapping operations in a variety of materials. The MIRANDA TOOLS HSS Hand Tap Straight Flute Serial SO3 Type Ground Thread Coarse Pitch, Size M8.0 x 1.25 mm (Set of 3) is built for professionals who require dependable performance in workshops, industrial settings, and maintenance tasks.With its robust construction and precise geometry, the MIRANDA TOOLS HSS Hand Tap Straight Flute Serial SO3 Type Ground Thread Coarse Pitch, Size M8.0 x 1.25 mm (Set of 3) provides excellent chip evacuation, reduced cutting resistance, and improved surface finish. This makes it a versatile choice for machinists, engineers, and technicians seeking accuracy and efficiency. Whether used for general-purpose threading or specialized tasks, the MIRANDA TOOLS HSS Hand Tap Straight Flute Serial SO3 Type Ground Thread Coarse Pitch, Size M8.0 x 1.25 mm (Set of 3) guarantees reliability and ease of use. Its high-quality material and superior workmanship ensure long-lasting performance, making it an essential addition to any professional toolkit.

Thread : Ground Thread

Material : High Speed Steel

Type of Product : HSS Hand Tap

Flute Type : Straight Flute

Pitch Type : Coarse Pitch

Finish Type : Bright Finish

Usage For : Internal Thread formation in Components

Country of Origin : India

Tap Type : Serial SO3

Standard Compliance : IS 6175 - Part 1, 2 & 3 - 1992

Page 1 of 116 results

Top Selling Hand Taps Products Price List for November 2025

Product Name	Specifications	Expected Price	Dispatch Time	Discount
Inder 3/4" - 14" BSP Carbon Steel Cut Thread Right Hand Taps 1005F	Cutting Type Right Hand \| Material Carbon Steel	₹1,073	4 days	8.06% OFF
Addison MFP Non-Serial HSS Ground Thread Hand Tap (Dia 3.5 mm, Pitch 0.35 mm)	Diameter 3.5 mm \| Material HSS	₹1,167	4 days	27.07% OFF
TOTEM BSF Straight Flute HSS Hand Tap 12.7 mm (1/2 Inch)	Grade 949-1969 \| Material HSS	₹1,651	2 days	--
TOTEM 2.5 x 0.45mm TiN Gold HSS Straight Fluted Tap	Finish Type TiN Gold \| Material HSS	₹660	2 days	23.59% OFF
TOTEM 1/8 Inch HSS BSW TiN Gold Straight Fluted Tap	Finish Type TiN Gold \| Grade BS - 949	₹435	2 days	25.68% OFF
TOTEM 2 x 0.4mm TiN Gold HSS Straight Fluted Tap	Finish Type TiN Gold \| Material HSS	₹671	2 days	22.32% OFF
TOTEM 3/16 Inch HSS UNC TiN Gold Straight Fluted Tap	Finish Type TiN Gold \| Grade BS - 949	₹565	4 days	6.11% OFF
Inder 1" - 8 UNC RH Carbon Steel Cut Type Hand Taps 1003T	--	₹1,769	4 days	10.07% OFF

This data was last updated on 26/11/2025

Know All About Hand Taps Here

Hand taps, essential tools in metalworking, are designed for threading holes manually. These precision tools create internal threads with accuracy and efficiency. Commonly used with a tap wrench, they come in various sizes and materials, ensuring versatility for different applications.

Key Features:
a) Precision Threading: They provide accurate and controlled threading in various materials.
b) Versatility: Different sizes and materials are available to suit diverse threading needs.
c) Ease of Use: Typically used with a tap wrench for manual operation.
d) Durability: Crafted from high-quality materials to ensure longevity and resistance to wear.

How do Hand Taps Work?

Hand tap tool gradually cut into a pre-drilled hole, forming threads that match the tap's specifications. The process involves several steps:

i) Pre-Drilling: With the help of these taps or drilling tools, a hole is drilled into the material to accommodate the tap.
ii) Alignment: The hand tap machine is aligned with the hole, ensuring proper threading.
iii) Cutting Threads: With each turn, the hand tap cuts into the material, creating internal threads.
iv) Retraction: Periodically, the tap is reversed to break and clear chips for smoother threading.

Key Advantages:
a) Manual Control: Users have precise control over the threading process.
b) Versatile Applications: Suitable for various materials, including metal, wood, and plastic.
c) Cost-Effective: Ideal for small-scale projects where a power tap may not be necessary.

Where are they commonly used?

Hand tap tools are indispensable tools in metalworking and machining, widely used for threading operations. These versatile tools find typical applications in various industries, providing precision and efficiency in creating internal threads in materials such as metal and wood. Let's explore where hand taps are commonly used and the available types.

Common hand-taps uses:
They are frequently employed in the following industries and scenarios:

i) Metalworking: Hand tap tools are extensively used in metalworking operations, including manufacturing, fabrication, and machining processes.
ii) Woodworking: They facilitate the creation of threaded holes in wooden components in carpentry and woodworking.
iii) Repair and Maintenance: Hand taps are essential for repair and maintenance tasks, allowing for the restoration of threaded connections.

Shop this product and other useful tools like cutting blades from our website at wholesale rates.

What are the types of Hand Taps?

Different hand taps cater to specific threading needs:

1. Straight Flute Taps: Ideal for general-purpose threading, ensuring efficient chip evacuation.
2. Spiral Flute Taps: Designed for tapping blind holes, promoting effective chip removal and smoother operation.

Professionals in the tools and cutting industry can explore various hand taps to meet their specific requirements, ensuring precision and durability in threading operations. As part of the tools and missing category, these tools play a crucial role in maintaining accuracy and efficiency in various machining applications.

What are the advantages of Hand Taps?

Hand taps offer a range of advantages, making them indispensable tools in metalworking and woodworking. Hand taps uses and benefits include:

i) Versatility: They are versatile tools suitable for various applications, from creating threads in metal to woodworking projects.
ii) Ease of Use: Hand tap tools are user-friendly for manual operation, allowing for precise control during threading operations and working with other inserts.
iii) Cost-Effective: They are a cost-effective solution compared to automated threading machines, making them accessible for various industries and workshops.
iv) Portability: They are portable and do not require a power source, providing flexibility in diverse working environments.

Why Choose Industrybuying?

Industrybuying is a reliable source for procuring hand tap machines and related accessories, offering a seamless shopping experience. Here's why you should choose Industrybuying:

a) Wide Selection: Industrybuying provides a diverse range of hand taps, ensuring customers find the right tool for their needs.
b) Quality Assurance: All products, including hand taps, undergo stringent quality checks, ensuring durability and performance.
c) Convenient Online Platform: With a user-friendly website, Industrybuying makes the selection and purchase process convenient, allowing customers to easily browse and buy hand taps.
d) Expert Guidance: Industrybuying provides specialist guidance and product information, assisting customers in making informed decisions.
e) Prompt Delivery: Timely delivery of products, including hand taps, is a priority, ensuring customers receive their orders on time.

What brands of hand tapes are available at Industrybuying?

Explore a wide array of hand tap machine from renowned brands in the tools and cutting category. These brands prioritise precision, durability, and efficiency in their products:

a) TOTEM: Renowned for its extensive range of high-quality hand tools, Totem offers reliable hand taps and cutters designed for various threading applications.
b) YG-1: A trusted name in the cutting tool industry, YG-1 provides precision-engineered hand taps suitable for diverse machining needs.
c) Dolphin: With a legacy of excellence, Dolphin offers a comprehensive selection of hand taps, ensuring top-notch performance and longevity.