• Home /
• All Brands /
• Crystal

Have a question? Call us now at +91 9650660070

Crystal Products Online

Showing 32 out of 32 products

Sort by

Recommended New Price : Low to High Price : High to Low

Ships within 2 days

Crystal 76.2 mm (3 Inch) Hardened and Ground V Block With Clamp Set of 2 Pcs 1712P

By Crystal

Set of 2 piece

₹5,781  

The 'V' Block have two 'V' angles of size to take jobs of dimention. By means of clamp the work can be held rigidly to the 'V’ Block. The top 'V' and bottom 'V' are parallel within ± 3 micron and it's squareness to the end faces and height variation to the 'V' Block in a pair is within ± 3 micron.
Features:
'V' Block are hardened and ground to 60 HRC.
Precision 'V' Block for Toll Room, Inspection, Work, Assembly Shop.
All sides precision ground, Parallel and square.
'V' groove ground central and parallel two sides & base matched with ± 3 microns.
Supplied with clamp for holding job.
Hold square and round work.
Permits grinding ends of work square with sides.

Add to Cart Buy Now

Ships within 3 days

Crystal 152.4 mm (6 Inch) Hardened and Ground Magnetic V Block 1805HS

By Crystal

₹18,879  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 6 Inch 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 5 days

Crystal 203.2 mm (8 Inch) Hardened and Ground Magnetic V Block 1806HS

By Crystal

₹27,139  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 3 days

Crystal Demagnetiser 150 x 300 mm 2514S

By Crystal

₹8,967   ₹9,596

You save ₹629!

6.55% OFF

The "Crystal" plate Demagnetizer effectively removes surface residual magnetism from high speed steel, Chrome, Spearing Steel or die steel. As the magnetic poles contact he object to be demagnetized, the magnetism is released. Thick objects may be demagnetized by applying both ends to the Demagnetiser. "Crystal" Brand Demagnetizers are supplied with ON/OFF switch and additional foot switch for safety. Demagnetizers utilize 220 V single phase alternatives electrical current.

Add to Cart Buy Now

Related Searches

crystal sine bar

crystal v-blocks & clamping sets

crystal grinding vices

Ships within 3 days

Crystal AA-60101S Sine Bar (130 x 25 x 30 mm)

By Crystal

₹4,129   ₹4,293

You save ₹164!

3.83% OFF

Features :-
Made from high quality alloy steel.
Used for precision measurement, setting of angles.
Center distance between rollers is within ± 0.005mm.
Accuracy for squareness, Flatness & Parallelism is within 0.005mm.
Hardness-60 ± 2 RC & Tempered.
Disclaimer: The above item is non-refundable. Industrybuying does not bear any responsibility for any operational concerns you may experience with the purchased item

Add to Cart Buy Now

Ships within 3 days

Crystal Demagnetiser 150 x 150 mm 2512S

By Crystal

₹7,079  

The "Crystal" plate Demagnetizer effectively removes surface residual magnetism from high speed steel, Chrome, Spearing Steel or die steel. As the magnetic poles contact he object to be demagnetized, the magnetism is released. Thick objects may be demagnetized by applying both ends to the Demagnetiser. "Crystal" Brand Demagnetizers are supplied with ON/OFF switch and additional foot switch for safety. Demagnetizers utilize 220 V single phase alternatives electrical current.

Add to Cart Buy Now

Ships within 2 days

Crystal 50.8mm(2 Inch) Hardened and Ground V Block With Clamp Set of 2 Pcs 1711P

By Crystal

Set of 2 piece

₹3,893  

The 'V' Block have two 'V' angles of size to take jobs of dimention. By means of clamp the work can be held rigidly to the 'V’ Block. The top 'V' and bottom 'V' are parallel within ± 3 micron and it's squareness to the end faces and height variation to the 'V' Block in a pair is within ± 3 micron.
Features:
'V' Block are hardened and ground to 60 HRC.
Precision 'V' Block for Toll Room, Inspection, Work, Assembly Shop.
All sides precision ground, Parallel and square.
'V' groove ground central and parallel two sides & base matched with ± 3 microns.
Supplied with clamp for holding job.
Hold square and round work.
Permits grinding ends of work square with sides.

Add to Cart Buy Now

Ships within 5 days

Crystal 0-75 mm Hardened and Ground Precision Grinding Vice 4801H

By Crystal

₹7,079  

Hardened Grinding Vices, Ground Grinding Vices For high accuracy Light Machining, Grinding, Inspection or marking out of precision components. Vice can be used, standing on its base, sides, end or top. Guaranteed 0.005/100 mm for Parallelism, Flatness & Squareness with the vice in any position. Manufactured from high grade oil hardening steel, hardened & tempered to ensure stability & accuracy throughout the unit's working life.

Add to Cart Buy Now

Ships within 5 days

Crystal Transfer Block 50 x 75 x 75 mm Set of 2 Pcs 1553P

By Crystal

Set of 2 piece

₹4,247  

Transfer Blocks are very useful for grinding thin & odd shape jobs. It is used with magnetic chuck. Magnetic Transfer Blocks provide the simplest method of extending the flux of any magnetic chuck with parallel poles to support work pieces above the chuck face. They do not alter the pole spacing. Always place the laminations in line with inner poles of the chucks, and within the area of the inner poles. When setting up place chuck blocks so as that the maximum number of magnetic loops pass through the work pieces. In such cases, ensure that sufficient securing rivets remain to hold the laminations firmly together.

Add to Cart Buy Now

Ships within 5 days

Crystal 76.2 mm (3 Inch) Hardened and Ground Magnetic V Block Set of 2 Pcs 1802HP

By Crystal

Set of 2 piece

₹10,737  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 3 Inch 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 3 days

Crystal AA-60103S Sine Bar (350 x 55 x 80 mm)

By Crystal

₹8,141   ₹8,930

You save ₹789!

8.84% OFF

Features :-
Made from high quality alloy steel.
Used for precision measurement, setting of angles.
Center distance between rollers is within ± 0.005mm.
Accuracy for squareness, Flatness & Parallelism is within 0.005mm.
Hardness-60 ± 2 RC & Tempered.
Disclaimer: The above item is non-refundable. Industrybuying does not bear any responsibility for any operational concerns you may experience with the purchased item

Add to Cart Buy Now

Ships within 3 days

Crystal AA-60102S Sine Bar (245 x 40 x 60 mm)

By Crystal

₹5,073   ₹5,202

You save ₹129!

2.48% OFF

Features :-
Made from high quality alloy steel.
Used for precision measurement, setting of angles.
Center distance between rollers is within ± 0.005mm.
Accuracy for squareness, Flatness & Parallelism is within 0.005mm.
Hardness-60 ± 2 RC & Tempered.
Disclaimer: The above item is non-refundable. Industrybuying does not bear any responsibility for any operational concerns you may experience with the purchased item

Add to Cart Buy Now

Ships within 5 days

Crystal 0-125 mm Hardened and Ground Precision Grinding Vice 4804H

By Crystal

₹21,239  

Hardened Grinding Vices, Ground Grinding Vices For high accuracy Light Machining, Grinding, Inspection or marking out of precision components. Vice can be used, standing on its base, sides, end or top. Guaranteed 0.005/100 mm for Parallelism, Flatness & Squareness with the vice in any position. Manufactured from high grade oil hardening steel, hardened & tempered to ensure stability & accuracy throughout the unit's working life.

Add to Cart Buy Now

Ships within 5 days

Crystal 0-100 mm Hardened and Ground Precision Grinding Vice 4803H

By Crystal

₹12,979  

Hardened Grinding Vices, Ground Grinding Vices For high accuracy Light Machining, Grinding, Inspection or marking out of precision components. Vice can be used, standing on its base, sides, end or top. Guaranteed 0.005/100 mm for Parallelism, Flatness & Squareness with the vice in any position. Manufactured from high grade oil hardening steel, hardened & tempered to ensure stability & accuracy throughout the unit's working life.

Add to Cart Buy Now

Ships within 5 days

Crystal 0-90 mm Hardened and Ground Precision Grinding Vice 4802H

By Crystal

₹11,327  

Hardened Grinding Vices, Ground Grinding Vices For high accuracy Light Machining, Grinding, Inspection or marking out of precision components. Vice can be used, standing on its base, sides, end or top. Guaranteed 0.005/100 mm for Parallelism, Flatness & Squareness with the vice in any position. Manufactured from high grade oil hardening steel, hardened & tempered to ensure stability & accuracy throughout the unit's working life.

Add to Cart Buy Now

Ships within 2 days

Crystal Transfer Block 60 x 25 x 100 mm Set of 2 Pcs 1556P

By Crystal

Set of 2 piece

₹4,011  

Transfer Blocks are very useful for grinding thin & odd shape jobs. It is used with magnetic chuck. Magnetic Transfer Blocks provide the simplest method of extending the flux of any magnetic chuck with parallel poles to support work pieces above the chuck face. They do not alter the pole spacing. Always place the laminations in line with inner poles of the chucks, and within the area of the inner poles. When setting up place chuck blocks so as that the maximum number of magnetic loops pass through the work pieces. In such cases, ensure that sufficient securing rivets remain to hold the laminations firmly together.

Add to Cart Buy Now

Ships within 3 days

Crystal 25.4 mm (1 Inch) Hardened and Ground V Block With Clamp Set of 2 Pcs 1714P

By Crystal

Set of 2 piece

₹2,477  

The 'V' Block have two 'V' angles of size to take jobs of dimention. By means of clamp the work can be held rigidly to the 'V’ Block. The top 'V' and bottom 'V' are parallel within ± 3 micron and it's squareness to the end faces and height variation to the 'V' Block in a pair is within ± 3 micron.
Features:
'V' Block are hardened and ground to 60 HRC.
Precision 'V' Block for Toll Room, Inspection, Work, Assembly Shop.
All sides precision ground, Parallel and square.
'V' groove ground central and parallel two sides & base matched with ± 3 microns.
Supplied with clamp for holding job.
Hold square and round work.
Permits grinding ends of work square with sides.

Add to Cart Buy Now

Ships within 6 days

Crystal 4 Inch Hardened and Ground V Block With Clamp Set of 2 Pcs 1713P

By Crystal

Set of 2 piece

₹8,023  

The 'V' Block have two 'V' angles of size to take jobs of dimention. By means of clamp the work can be held rigidly to the 'V’ Block. The top 'V' and bottom 'V' are parallel within ± 3 micron and it's squareness to the end faces and height variation to the 'V' Block in a pair is within ± 3 micron.
Features:
'V' Block are hardened and ground to 60 HRC.
Precision 'V' Block for Toll Room, Inspection, Work, Assembly Shop.
All sides precision ground, Parallel and square.
'V' groove ground central and parallel two sides & base matched with ± 3 microns.
Supplied with clamp for holding job.
Hold square and round work.
Permits grinding ends of work square with sides.

Add to Cart Buy Now

Ships within 6 days

Crystal 50.8mm(2 Inch) Hardened and Ground Magnetic V Block Set of 2 Pcs 1803HP

By Crystal

Set of 2 piece

₹5,545  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 2 Inch 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 30 days

Crystal 4 Inch Hardened and Ground Magnetic V Block 1801HS

By Crystal

₹9,557  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 4 Inch 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 30 days

Crystal 4 Inch Hardened and Ground Magnetic V Block Set of 2 Pcs 1801HP

By Crystal

Set of 2 piece

₹21,239  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 4 Inch 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 30 days

Crystal Demagnetiser 150 x 100 mm 2511S

By Crystal

₹4,719  

The "Crystal" plate Demagnetizer effectively removes surface residual magnetism from high speed steel, Chrome, Spearing Steel or die steel. As the magnetic poles contact he object to be demagnetized, the magnetism is released. Thick objects may be demagnetized by applying both ends to the Demagnetiser. "Crystal" Brand Demagnetizers are supplied with ON/OFF switch and additional foot switch for safety. Demagnetizers utilize 220 V single phase alternatives electrical current.

Add to Cart Buy Now

Ships within 30 days

Crystal 203.2 mm (8 Inch) Hardened and Ground Magnetic V Block Set of 2 Pcs 1806HP

By Crystal

Set of 2 piece

₹47,199  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 30 days

Crystal 50.8mm(2 Inch) Hardened and Ground Magnetic V Block 1803HS

1

By Crystal

₹3,185  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 2 Inch 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 30 days

Crystal 152.4 mm (6 Inch) Hardened and Ground Magnetic V Block Set of 2 Pcs 1805HP

By Crystal

Set of 2 piece

₹29,499  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 6 Inch 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 30 days

Crystal Demagnetiser 350 x 350 mm 2515S

By Crystal

₹30,679  

The "Crystal" plate Demagnetizer effectively removes surface residual magnetism from high speed steel, Chrome, Spearing Steel or die steel. As the magnetic poles contact he object to be demagnetized, the magnetism is released. Thick objects may be demagnetized by applying both ends to the Demagnetiser. "Crystal" Brand Demagnetizers are supplied with ON/OFF switch and additional foot switch for safety. Demagnetizers utilize 220 V single phase alternatives electrical current.

Add to Cart Buy Now

Ships within 30 days

Crystal Transfer Block 50 x 20 x 100 mm Set of 2 Pcs 1557P

By Crystal

Set of 2 piece

₹3,303  

Transfer Blocks are very useful for grinding thin & odd shape jobs. It is used with magnetic chuck. Magnetic Transfer Blocks provide the simplest method of extending the flux of any magnetic chuck with parallel poles to support work pieces above the chuck face. They do not alter the pole spacing. Always place the laminations in line with inner poles of the chucks, and within the area of the inner poles. When setting up place chuck blocks so as that the maximum number of magnetic loops pass through the work pieces. In such cases, ensure that sufficient securing rivets remain to hold the laminations firmly together.

Add to Cart Buy Now

Ships within 30 days

Crystal Transfer Block 80 x 25 x 120 mm Set of 2 Pcs 1555P

By Crystal

Set of 2 piece

₹5,781  

Transfer Blocks are very useful for grinding thin & odd shape jobs. It is used with magnetic chuck. Magnetic Transfer Blocks provide the simplest method of extending the flux of any magnetic chuck with parallel poles to support work pieces above the chuck face. They do not alter the pole spacing. Always place the laminations in line with inner poles of the chucks, and within the area of the inner poles. When setting up place chuck blocks so as that the maximum number of magnetic loops pass through the work pieces. In such cases, ensure that sufficient securing rivets remain to hold the laminations firmly together.

Add to Cart Buy Now

Ships within 30 days

Crystal Transfer Block 50 x 50 x 100 mm Set of 2 Pcs 1554P

By Crystal

Set of 2 piece

₹4,129  

Transfer Blocks are very useful for grinding thin & odd shape jobs. It is used with magnetic chuck. Magnetic Transfer Blocks provide the simplest method of extending the flux of any magnetic chuck with parallel poles to support work pieces above the chuck face. They do not alter the pole spacing. Always place the laminations in line with inner poles of the chucks, and within the area of the inner poles. When setting up place chuck blocks so as that the maximum number of magnetic loops pass through the work pieces. In such cases, ensure that sufficient securing rivets remain to hold the laminations firmly together.

Add to Cart Buy Now

Ships within 30 days

Crystal Transfer Block 60 x 30 x 75 mm Set of 2 Pcs 1552P

By Crystal

Set of 2 piece

₹2,949  

Transfer Blocks are very useful for grinding thin & odd shape jobs. It is used with magnetic chuck. Magnetic Transfer Blocks provide the simplest method of extending the flux of any magnetic chuck with parallel poles to support work pieces above the chuck face. They do not alter the pole spacing. Always place the laminations in line with inner poles of the chucks, and within the area of the inner poles. When setting up place chuck blocks so as that the maximum number of magnetic loops pass through the work pieces. In such cases, ensure that sufficient securing rivets remain to hold the laminations firmly together.

Add to Cart Buy Now

Ships within 30 days

Crystal Transfer Block 50 x 35 x 100 mm Set of 2 Pcs 1551P

By Crystal

Set of 2 piece

₹3,893  

Transfer Blocks are very useful for grinding thin & odd shape jobs. It is used with magnetic chuck. Magnetic Transfer Blocks provide the simplest method of extending the flux of any magnetic chuck with parallel poles to support work pieces above the chuck face. They do not alter the pole spacing. Always place the laminations in line with inner poles of the chucks, and within the area of the inner poles. When setting up place chuck blocks so as that the maximum number of magnetic loops pass through the work pieces. In such cases, ensure that sufficient securing rivets remain to hold the laminations firmly together.

Add to Cart Buy Now

Ships within 30 days

Crystal 76.2 mm (3 Inch) Hardened and Ground Magnetic V Block 1802HS

By Crystal

₹5,899  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 3 Inch 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Previous Next

Page 1 of 1 results