• Home /
• All Brands /
• Crystal /
• Hand Tools /
• Clamps & Bolts /
• V-Blocks & Clamping Sets

Have a question? Call us now at +91 9650660070

Crystal V Blocks Clamping Sets

Showing 21 out of 21 products

Sort by

Recommended New Price : Low to High Price : High to Low

Ships within 5 days

Crystal 76.2 mm (3 Inch) Hardened and Ground Magnetic V Block Set of 2 Pcs 1802HP

By Crystal

Set of 2 piece

₹12,979  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 3 Inch 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 5 days

Crystal 203.2 mm (8 Inch) Hardened and Ground Magnetic V Block 1806HS

By Crystal

₹28,319  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 5 days

Crystal 4 Inch Hardened and Ground Magnetic V Block 1801HS

By Crystal

₹11,327  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 4 Inch 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 5 days

Crystal 50.8mm(2 Inch) Hardened and Ground Magnetic V Block 1803HS

1

By Crystal

₹3,775  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 2 Inch 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 5 days

Crystal 4 Inch Hardened and Ground V Block With Clamp Set of 2 Pcs 1713P

By Crystal

Set of 2 piece

₹9,557  

The 'V' Block have two 'V' angles of size to take jobs of dimention. By means of clamp the work can be held rigidly to the 'V’ Block. The top 'V' and bottom 'V' are parallel within ± 3 micron and it's squareness to the end faces and height variation to the 'V' Block in a pair is within ± 3 micron.
Features:
'V' Block are hardened and ground to 60 HRC.
Precision 'V' Block for Toll Room, Inspection, Work, Assembly Shop.
All sides precision ground, Parallel and square.
'V' groove ground central and parallel two sides & base matched with ± 3 microns.
Supplied with clamp for holding job.
Hold square and round work.
Permits grinding ends of work square with sides.

Add to Cart Buy Now

Ships within 5 days

Crystal 76.2 mm (3 Inch) Hardened and Ground Magnetic V Block 1802HS

By Crystal

₹7,079  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 3 Inch 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 5 days

Crystal 50.8mm(2 Inch) Hardened and Ground Magnetic V Block Set of 2 Pcs 1803HP

By Crystal

Set of 2 piece

₹6,607  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 2 Inch 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 5 days

Crystal 152.4 mm (6 Inch) Hardened and Ground Magnetic V Block 1805HS

By Crystal

₹22,419  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 6 Inch 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 5 days

Crystal 4 Inch Hardened and Ground Magnetic V Block Set of 2 Pcs 1801HP

By Crystal

Set of 2 piece

₹24,779  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 4 Inch 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 5 days

Crystal 50.8mm(2 Inch) Hardened and Ground V Block With Clamp Set of 2 Pcs 1711P

By Crystal

Set of 2 piece

₹4,719  

The 'V' Block have two 'V' angles of size to take jobs of dimention. By means of clamp the work can be held rigidly to the 'V’ Block. The top 'V' and bottom 'V' are parallel within ± 3 micron and it's squareness to the end faces and height variation to the 'V' Block in a pair is within ± 3 micron.
Features:
'V' Block are hardened and ground to 60 HRC.
Precision 'V' Block for Toll Room, Inspection, Work, Assembly Shop.
All sides precision ground, Parallel and square.
'V' groove ground central and parallel two sides & base matched with ± 3 microns.
Supplied with clamp for holding job.
Hold square and round work.
Permits grinding ends of work square with sides.

Add to Cart Buy Now

Ships within 5 days

Crystal 203.2 mm (8 Inch) Hardened and Ground Magnetic V Block Set of 2 Pcs 1806HP

By Crystal

Set of 2 piece

₹56,639  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 5 days

Crystal 152.4 mm (6 Inch) Hardened and Ground Magnetic V Block Set of 2 Pcs 1805HP

By Crystal

Set of 2 piece

₹35,399  

Accuracy for Squareness Flatness & Parallelism within 5 micron. 'V' Blocks are required for Quality Control, Tool Room and Standard Room. "Crystal" Brand Magnetic 'V' Blocks have high magnetic pull, hence they can be used fro drilling and grinding (both wet and dry) and even for light milling work.
The 'V' Block has a total three magnetic surfaces. Top and Bottom with 90 'V' angle and end surface opposite to switch. All three magnetic surfaces and the two sides are carefully ground. Their accuracy for flatness, parallelism and squareness is within 0.005 mm for 6 Inch 'V' Blocks. When turned "ON" all three magnetic surfaces are activated Simultaneously.
The permanent magnet holds the work firmly in the 'V' and if the block rests on a magnetically conductive surface, it is held firmly to this surface. The magnetic pull is constant and will not decrease eveb after long use. The magnetic system being shielded from penetration of moisture, cannot be damaged by coolants or other fluids.

Add to Cart Buy Now

Ships within 5 days

Crystal 76.2 mm (3 Inch) Hardened and Ground V Block With Clamp Set of 2 Pcs 1712P

By Crystal

Set of 2 piece

₹6,961  

The 'V' Block have two 'V' angles of size to take jobs of dimention. By means of clamp the work can be held rigidly to the 'V’ Block. The top 'V' and bottom 'V' are parallel within ± 3 micron and it's squareness to the end faces and height variation to the 'V' Block in a pair is within ± 3 micron.
Features:
'V' Block are hardened and ground to 60 HRC.
Precision 'V' Block for Toll Room, Inspection, Work, Assembly Shop.
All sides precision ground, Parallel and square.
'V' groove ground central and parallel two sides & base matched with ± 3 microns.
Supplied with clamp for holding job.
Hold square and round work.
Permits grinding ends of work square with sides.

Add to Cart Buy Now

Ships within 5 days

Crystal Transfer Block 50 x 20 x 100 mm Set of 2 Pcs 1557P

By Crystal

Set of 2 piece

₹4,011  

Transfer Blocks are very useful for grinding thin & odd shape jobs. It is used with magnetic chuck. Magnetic Transfer Blocks provide the simplest method of extending the flux of any magnetic chuck with parallel poles to support work pieces above the chuck face. They do not alter the pole spacing. Always place the laminations in line with inner poles of the chucks, and within the area of the inner poles. When setting up place chuck blocks so as that the maximum number of magnetic loops pass through the work pieces. In such cases, ensure that sufficient securing rivets remain to hold the laminations firmly together.

Add to Cart Buy Now

Ships within 5 days

Crystal Transfer Block 60 x 25 x 100 mm Set of 2 Pcs 1556P

By Crystal

Set of 2 piece

₹4,837  

Transfer Blocks are very useful for grinding thin & odd shape jobs. It is used with magnetic chuck. Magnetic Transfer Blocks provide the simplest method of extending the flux of any magnetic chuck with parallel poles to support work pieces above the chuck face. They do not alter the pole spacing. Always place the laminations in line with inner poles of the chucks, and within the area of the inner poles. When setting up place chuck blocks so as that the maximum number of magnetic loops pass through the work pieces. In such cases, ensure that sufficient securing rivets remain to hold the laminations firmly together.

Add to Cart Buy Now

Ships within 5 days

Crystal Transfer Block 80 x 25 x 120 mm Set of 2 Pcs 1555P

By Crystal

Set of 2 piece

₹6,843  

Transfer Blocks are very useful for grinding thin & odd shape jobs. It is used with magnetic chuck. Magnetic Transfer Blocks provide the simplest method of extending the flux of any magnetic chuck with parallel poles to support work pieces above the chuck face. They do not alter the pole spacing. Always place the laminations in line with inner poles of the chucks, and within the area of the inner poles. When setting up place chuck blocks so as that the maximum number of magnetic loops pass through the work pieces. In such cases, ensure that sufficient securing rivets remain to hold the laminations firmly together.

Add to Cart Buy Now

Ships within 5 days

Crystal Transfer Block 50 x 50 x 100 mm Set of 2 Pcs 1554P

By Crystal

Set of 2 piece

₹4,955  

Transfer Blocks are very useful for grinding thin & odd shape jobs. It is used with magnetic chuck. Magnetic Transfer Blocks provide the simplest method of extending the flux of any magnetic chuck with parallel poles to support work pieces above the chuck face. They do not alter the pole spacing. Always place the laminations in line with inner poles of the chucks, and within the area of the inner poles. When setting up place chuck blocks so as that the maximum number of magnetic loops pass through the work pieces. In such cases, ensure that sufficient securing rivets remain to hold the laminations firmly together.

Add to Cart Buy Now

Ships within 5 days

Crystal Transfer Block 60 x 30 x 75 mm Set of 2 Pcs 1552P

By Crystal

Set of 2 piece

₹3,539  

Transfer Blocks are very useful for grinding thin & odd shape jobs. It is used with magnetic chuck. Magnetic Transfer Blocks provide the simplest method of extending the flux of any magnetic chuck with parallel poles to support work pieces above the chuck face. They do not alter the pole spacing. Always place the laminations in line with inner poles of the chucks, and within the area of the inner poles. When setting up place chuck blocks so as that the maximum number of magnetic loops pass through the work pieces. In such cases, ensure that sufficient securing rivets remain to hold the laminations firmly together.

Add to Cart Buy Now

Ships within 5 days

Crystal Transfer Block 50 x 35 x 100 mm Set of 2 Pcs 1551P

By Crystal

Set of 2 piece

₹4,719  

Transfer Blocks are very useful for grinding thin & odd shape jobs. It is used with magnetic chuck. Magnetic Transfer Blocks provide the simplest method of extending the flux of any magnetic chuck with parallel poles to support work pieces above the chuck face. They do not alter the pole spacing. Always place the laminations in line with inner poles of the chucks, and within the area of the inner poles. When setting up place chuck blocks so as that the maximum number of magnetic loops pass through the work pieces. In such cases, ensure that sufficient securing rivets remain to hold the laminations firmly together.

Add to Cart Buy Now

Ships within 5 days

Crystal 25.4 mm (1 Inch) Hardened and Ground V Block With Clamp Set of 2 Pcs 1714P

By Crystal

Set of 2 piece

₹2,949  

The 'V' Block have two 'V' angles of size to take jobs of dimention. By means of clamp the work can be held rigidly to the 'V’ Block. The top 'V' and bottom 'V' are parallel within ± 3 micron and it's squareness to the end faces and height variation to the 'V' Block in a pair is within ± 3 micron.
Features:
'V' Block are hardened and ground to 60 HRC.
Precision 'V' Block for Toll Room, Inspection, Work, Assembly Shop.
All sides precision ground, Parallel and square.
'V' groove ground central and parallel two sides & base matched with ± 3 microns.
Supplied with clamp for holding job.
Hold square and round work.
Permits grinding ends of work square with sides.

Add to Cart Buy Now

Ships within 30 days

Crystal Transfer Block 50 x 75 x 75 mm Set of 2 Pcs 1553P

By Crystal

Set of 2 piece

₹5,073  

Transfer Blocks are very useful for grinding thin & odd shape jobs. It is used with magnetic chuck. Magnetic Transfer Blocks provide the simplest method of extending the flux of any magnetic chuck with parallel poles to support work pieces above the chuck face. They do not alter the pole spacing. Always place the laminations in line with inner poles of the chucks, and within the area of the inner poles. When setting up place chuck blocks so as that the maximum number of magnetic loops pass through the work pieces. In such cases, ensure that sufficient securing rivets remain to hold the laminations firmly together.

Add to Cart Buy Now

Previous Next

Page 1 of 1 results